AVSPARE.COM
parts catalog

MANIFOLD ASSY_EGR COOLER 7096176C1 - Caterpillar



7096176C1 MANIFOLD ASSY_EGR COOLER Caterpillar parts MANIFOLD
Rating:
31
Alternative (cross code) number:
CA7096176C1
70961-76C1
7096176C1
Caterpillar 7096176C1 MANIFOLD ASSY_EGR COOLER

Buy MANIFOLD ASSY_EGR COOLER 7096176C1 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 7
 
  For full view, you need register

Information:

Removal Procedure
Start By:
Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic System Pressure - Release" for the correct procedure.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Cylinders equipped with lock valves can remain pressurized for very long periods of time, even with the hoses removed.Failure to relieve pressure before removing a lock valve or disassembling a cylinder can result in personal injury or death.Ensure all pressure is relieved before removing a lock valve or disassembling a cylinder.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00927978
Remove cover (1) from the end of boom (2) .
Illustration 2 g00927982
Release the hydraulic pressure from the cylinder. Refer to Disassembly and Assembly, "Hydraulic System Pressure - Release" for the correct procedure.
Remove lock valve (3) from cylinder (4) .
Illustration 3 g00927983
Remove two backup rings (5) , O-ring seal (6) , O-ring seal (7) , backup ring (8) , O-ring seal (9) and O-ring seal (10) from lock valve (3) .Installation Procedure
Clean all parts and inspect all parts. If any parts are worn or damaged, use new Caterpillar parts for replacement.
Illustration 4 g00927983
Install two backup rings (5) , O-ring seal (6) , O-ring seal (7) , backup ring (8) , O-ring seal (9) and O-ring seal (10) onto lock valve (3) . Lubricate all O-ring seals and all backup rings with the lubricant that is being sealed.
Illustration 5 g00927982
Install lock valve (3) into cylinder (4) . Tighten the lock valve to a torque of 147 5 N m (108 4 lb ft).
Illustration 6 g00927978
Install cover (1) to the end of boom (2) .

Caterpillar parts catalog:

Caterpillar parts catalog
CT13 SCR ON HIGHWAY TRUCK ENGINE JFB00001-UP
CT13 ON HIGHWAY TRUCK ENGINE KBK00001-UP
CT11 ON HIGHWAY TRUCK ENGINE EBC00001-UP
CT13 SCR ON HIGHWAY TRUCK ENGINE JFB00001-UP
CT13 ON HIGHWAY TRUCK ENGINE KBK00001-UP
CT11 ON HIGHWAY TRUCK ENGINE EBC00001-UP
CT13 ON HIGHWAY TRUCK ENGINE KBK00001-UP
CT11 ON HIGHWAY TRUCK ENGINE EBC00001-UP
CT13 ON HIGHWAY TRUCK ENGINE KBK00001-UP


Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.