parts catalog

MARKER-TERMINAL 3844349 - Caterpillar

3844349 MARKER-TERMINAL Caterpillar parts G3516H
Alternative (cross code) number:
Caterpillar 3844349 MARKER-TERMINAL

Buy MARKER-TERMINAL 3844349 Caterpillar genuine, new aftermarket tractor parts with delivery

Compatible equipment models: 3844349:

GENERATOR SET  G3516H   Caterpillar
Number on catalog scheme: 17
  For full view, you need register


Illustration 73 g01117573
Use Tooling (D) and install retaining ring (61).
Turn the main pump housing over 180 degrees.
Illustration 74 g01117568
Install two rings (57) on each pistons (56).
Illustration 75 g01117567
Install pistons (56) in the piston's original locations in the pump rotating groups.
Illustration 76 g01117565
Install retaining plates (54) and centering pins (55) in the original positions over the pistons. Make sure that the screw holes in the retaining plates are in alignment with the screw holes in the pump rotating groups.
Illustration 77 g01117564
Apply Tooling (V) on the threads of socket head screws (53).
Install the socket head screws in order to hold retaining plates (54) to the pump rotating groups. Tighten the socket head screws evenly.
Install gasket (52).
Illustration 78 g01117563
Apply petroleum jelly to bevel spring washers (51) and spacer (50) in order to prevent bevel spring washers (51) and spacer (50) from falling out of barrel (49) during installation.
Illustration 79 g01125165
(49) Cylinder barrel. (50) Spacer. (51) Bevel washers.
Note: Bevel spring washers (51) are not flat. These washers should be installed so that the washers provide the maximum amount of height.
Install spacers (50) and four bevel spring washers (51) in each barrels (49), as shown. Note: Use the spacer that was determined in Steps 1 through 41.
Illustration 80 g01117562
Install barrels (49) in the cylinder barrel's original locations on the pump rotating groups.
Illustration 81 g01125166
Install dowels (47) in the main pump housing.
Illustration 82 g01125155
(S) Suction side
Apply petroleum jelly under both port plates (48) prior to installation.
Place each port plates (48) into position on the head assembly, as shown.
Illustration 83 g01125157
Fasten Tooling (B) and a suitable lifting device to head assembly (6), as shown. Place the head assembly in position on the main hydraulic pump.
Install bolts (5) that hold the head assembly to the main hydraulic pump.
Torque bolts (5) to 240 40 N m (175 30 lb ft), while you turn the pump shaft.
Install the drain plug.
Illustration 84 g01123653
Install tube assembly (4).
Illustration 85 g01123648
Install manifold (3) and bolts (2).
Illustration 86 g01123647
Install drain plug (1).
Remove the main hydraulic pump from Tooling (A). End By:
Install the main hydraulic pump. Refer to Disassembly and Assembly, "Piston Pump (Main Hydraulic) - Install".
Install the saw pump. Refer to Disassembly and Assembly, "Piston Pump (Saw) - Install".

Caterpillar parts catalog:

Caterpillar parts catalog
G3516H Generator Set NWJ00001-UP
G3516H Generator Set NWH00001-UP
G3512H Generator Set GF400001-UP
G3512H Generator Set GF500001-UP
G3516H Generator Set GLM00001-UP
G3516H Generator Set GLN00001-UP

Parts marker Caterpillar catalog:

3512, 3512B, 3512C, 3516, 3516B, 3516C, C175-16, C175-20, G3516H
3512, 3512B, 3512C, 3516, 3516B, 3516C, C175-16, C175-20, G3516H
3512B, 3512C, 3516B, 3516C, C175-16, C175-20, G3516H
3512, 3512B, 3512C, 3516, 3516B, 3516C, C175-16, C27, C32, G3516H
3512, 3516, C27, C32, G3516H
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.