AVSPARE.COM
parts catalog

MOUNTING GP-WORK TOOL 1694967 - Caterpillar



1694967 MOUNTING GP-WORK TOOL Caterpillar parts G112, MP15, MP318, P215, P360, S305, VHC-30, VHP-30, VHS-50, VPG-25, VT30, VT50 MOUNTING
Rating:
16
Alternative (cross code) number:
CA1694967
169-4967
1694967
Caterpillar 1694967 MOUNTING GP-WORK TOOL

Buy MOUNTING GP-WORK TOOL 1694967 Caterpillar genuine, new aftermarket tractor parts with delivery
CRUSHER, SHEAR-DEMOLITION/SCRAP,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below
The ROP Shop Genuine OEM PTO Switch fits Simplicity 1694964 1694966 1694967 1694968 1694969
$27.49
 

02 Dec 2020

-: -
The ROP Shop Genuine OEM PTO Switch fits Simplicity 1694964 1694966 1694967 1694968 1694969
New Genuine OEM PTO SWITCH || Fits Simplicity 1694964 1694966 1694967 1694968 1694969 || No. of Positions - 2, No. of Terminals - 2 || Push/Pull Yellow Knob, Snap Mount || Quality Aftermarket Part with 1 Year Warranty
Number on catalog scheme:
 
  For full view, you need register

Compatible equipment models: 1694967:

CRUSHER  P360   VHC-30  
GRAPPLE-MECHANICAL  G112   VPG-25  
MULTI PROCESSOR  MP15   MP318   VT30   VT50  
PULVERIZER  P215   VHP-30  
SHEAR-DEMOLITION/SCRAP  S305   VHS-50   Caterpillar

Information:


Install the cartridge pin with the mark (X) on the outside of the track roller frame. Position the mark (X) to the top or to the bottom of the vertical centerline.
Illustration 3 g00767260
Install Tooling (F) and install cartridge pins (14) in the major bogie. Install the cartridge pin in the major bogie sufficiently in order to allow the plate and the retaining ring to be installed.
Illustration 4 g00765980
Illustration 5 g00767280
Install rubber stopper (15) to 3.0 1.0 mm (0.118 0.039 inch) below the surface of the pins.
Add 60 3 cc of Tooling (J) to cartridge pins (14).
Install plug (13) in the end of each rubber stopper.
Install plugs (16) in each side of the track roller frame.
Install plate (12) in each side of the track roller frame.
Use Tooling (D) to install retaining ring (11) on each side of the track roller frame.
Repeat Steps 5 through 14 for the remainder of the major bogies.
Illustration 6 g00767284Note: The minor bogie must be installed with the part number or the words THIS SIDE OUT toward the outside of the major bogie.
Position minor bogie (10) in the major bogie.
Apply Tooling (H) to the bores of the major bogie and to the bores of the minor bogie.
Illustration 7 g00767289
Illustration 8 g00765892
Install the cartridge pin with the mark (X) on the outside of the track roller frame. Position the mark (X) to the top or to the bottom of the vertical centerline.
Use Tooling (F) to install cartridge pins (8) in the major bogie and in the minor bogie. The cartridge pins must be level with the outside surface of the major bogie.
Install rubber stoppers (9) to 3.0 1.0 mm (0.118 0.039 inch) below the surface of the pins.
Add 60 3 cc of Tooling (J) to the cartridge pins.
Install plug (7) in the end of each rubber stopper.
Repeat Steps 16 through 21 for the remainder of the minor bogies.
Illustration 9 g00765891
Install track guides (5), the washers, and bolts (6) on the major bogies. Tighten bolts (6) to a torque of 475 50 N m (350 37 lb ft).
Illustration 10 g00765890
Use a strap and a suitable lifting device in order to support track roller (4). Install the track roller on the minor bogie. Note: The single flange track roller weighs 88 kg (195 lb). The double flange track roller weighs 98 kg (215 lb).
Install caps (3), the washers, and bolts (2). Tighten bolts (2) to a torque of 750 70 N m (550 50 lb ft). Note: Tighten the bolt on the abutment side first. "Tighten first" is stamped on caps (3).
Repeat Steps 24 and 25 for all of the other track rollers.
Install the track idlers. Refer to Disassembly and Assembly, "Idler - Install" for the correct procedure.
Illustration 11 g00765889
Install Tooling (A) on the major bogies. Use a suitable lifting device in order to turn the track roller frame in the upright position.
Illustration 12 g00765888Note: Lower the temperature of the bearings before installation.
If two bearings (1) were removed, install two new bearings in the sides of the track

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
G112 G115 G125 G140 Mechanical Grapple ADN00001-UP (MACHINE)
G112 G115 G125 G140 MECHANICAL GRAPPLE BNZ00001-UP (MACHINE)
VPG-25, VPG-35, VPG-45 and VPG-55 Mechanical Grapple CHK00001-UP (MACHINE)


Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.