AVSPARE.COM
parts catalog

MOUNTING G 7A1357 - Caterpillar



7A1357 MOUNTING G Caterpillar parts MOUNTING
Rating:
51
Alternative (cross code) number:
CA7A1357
7A-1357
7A1357
Caterpillar 7A1357 MOUNTING G

Buy MOUNTING G 7A1357 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 1 g01234186
Schematic for the engine temperature sensors
Test Step 1. Inspect Electrical Connectors and Wiring
Remove the electrical power from the ECM.
Illustration 2 g01193815
Sensor locations (typical left side engine view)
(1) Engine coolant temperature sensor
(2) Intake manifold air temperature sensor
(3) Fuel temperature sensor
(4) J2/P2 ECM connectors
Thoroughly inspect the connectors for sensors (1), (2), and (3). Also, thoroughly inspect connectors (4). Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect".
Illustration 3 g01193814
P2 ECM connector
(P2-13) Engine coolant temperature
(P2-30) Common for the engine temperature sensors
(P2-56) Intake manifold air temperature
(P2-62) Fuel temperature
Illustration 4 g01155187
Connector for the temperature sensors
(1) Sensor signal
(2) Sensor return
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the temperature sensors.
Check the allen head screws for each ECM connector for the proper torque. Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect" for the correct torque values.
Check the harness and the wiring for abrasions and for pinch points from each of the temperature sensors to the ECM connector. Expected Result:All connectors, pins, and sockets are completely coupled and inserted. The harness and wiring are free of corrosion, of abrasion, and of pinch points.Results:
OK - The connectors and wiring appear to be OK. Proceed to Test Step 2.
Not OK - There is a problem in the connectors and/or wiring.Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled.Verify that the repair eliminates the problem.STOPTest Step 2. Check for Active Diagnostic Codes
Connect the Caterpillar Electronic Technician (ET) to the service tool connector.
Restore the electrical power to the ECM.
Monitor the active diagnostic code screen on Cat ET. Check and record any active diagnostic codes. Note: Wait at least 30 seconds in order for the diagnostic codes to become active.
Look for a 03 diagnostic code or a 04 diagnostic code. Expected Result:No diagnostic codes are active.Results:
OK - No diagnostic codes are active. The problem appears to be resolved.Repair: The problem may have been related to a faulty connection in the harness. Carefully reinspect the connectors and wiring. Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect".STOP
Not OK - A 04 diagnostic code is active at this time. Proceed to Test Step 3.
Not OK - A 03 diagnostic code is active at this time. Proceed to Test Step 4.Test Step 3. Disconnect the Suspect Sensor in Order to Create an Open Circuit
Remove the electrical power from the ECM.
Disconnect the suspect sensor from the engine harness.
Restore the electrical power to the ECM. Wait at least 30 seconds for activation of the diagnostic codes.
Access the "Active Diagnostic Codes" screen on Cat ET and check for an active 03 diagnostic code for the suspect sensor.
Remove the electrical power from the ECM. Expected Result:A 03 diagnostic code is now active for the suspect sensor.Results:
OK - A 04 diagnostic code was active before disconnecting the sensor. A 03 diagnostic code became active after the sensor was disconnected. There may be a problem


Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.