AVSPARE.COM
parts catalog

MUFFLER & MOUNTING GP 4646606 - Caterpillar



4646606 MUFFLER & MOUNTING GP Caterpillar parts MUFFLER
Rating:
26
Alternative (cross code) number:
CA4646606
464-6606
4646606
Caterpillar 4646606 MUFFLER & MOUNTING GP

Buy MUFFLER & MOUNTING GP 4646606 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 4
 
  For full view, you need register

Information:

Probable Causes
Air inlet or exhaust system
Engine speed/timing sensors
Atmospheric pressure sensor
Intake manifold pressure sensor
"Fuel Position" and/or "FRC Fuel Limit"
Flash file
Fuel quality
Valve adjustmentRecommended Actions
Air Inlet or Exhaust System
Check the air inlet system for restrictions and for leaks.
Check for an air filter restriction.
Perform a visual inspection of the air inlet piping for restrictions and for leaks.
Ensure that the turbocharger is in good repair.
Check the exhaust system for restrictions.
Repair any leaks that were found. Remove any restrictions that were found. Replace any damaged components. Engine Speed/Timing Sensors
Check the calibration of the engine speed/timing sensors. Refer to Troubleshooting, "Timing - Calibrate".
Verify that the crankshaft and the camshaft drive gears are set with the proper orientation. Refer to the Disassembly and Assembly manual. Atmospheric Pressure Sensor
Check the atmospheric pressure sensor for dirt and/or for debris. Remove any dirt and/or debris that is present. The correct reading for the atmospheric pressure is between 50 kPa (7.25 psi) and 100 kPa (14.5 psi).Intake Manifold Pressure Sensor, "Fuel Position", and/or "FRC Fuel Limit"
Monitor the status of "Fuel Position" and "Rated Fuel Limit" while the engine is operating under full load. If "Fuel Position" equals "Rated Fuel Limit" and "Fuel Position" is less than "FRC Fuel Limit", the Electronic Control Module (ECM) is providing the correct control. Otherwise, proceed to the next Step.
Verify that there are no active diagnostic codes for the intake manifold pressure sensor.
Monitor the status of "Intake Manifold Pressure" and "Atmospheric Pressure" on Caterpillar Electronic Technician (ET). When the engine is not running, "Intake Manifold Pressure" should be 0 kPa (0 psi). Note: A problem with the "FRC Fuel Limit" will only cause black smoke during acceleration. A problem with the "FRC Fuel Limit" will not cause black smoke during steady state operation.Flash File
Verify that the correct flash file is installed in the ECM. Refer to Troubleshooting, "ECM Software - Install" for information.Fuel Quality
Cold weather adversely affects the characteristics of the fuel. Refer to Operation and Maintenance Manual for information on improving the characteristics of the fuel during cold weather operation.Valve Adjustment
Check for the correct valve adjustment. Refer to Systems Operation/Testing and Adjusting for information on adjustment of the valves.

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
TL1055C Telehandler KDE01628-UP (MACHINE) POWERED BY C4.4 Engine
TL1255C Telehandler DHW01422-UP (MACHINE) POWERED BY C4.4 Engine


Parts muffler Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.