AVSPARE.COM
parts catalog

NOZZLE GP-INJ 2333488 - Caterpillar



2333488 NOZZLE GP-INJ Caterpillar parts NOZZLE
Rating:
76
Alternative (cross code) number:
CA2333488
233-3488
2333488
Caterpillar 2333488 NOZZLE GP-INJ

Buy NOZZLE GP-INJ 2333488 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 1 g00289119
Pressure setting for the charge pressure relief valve (above case pressure) ... 2470 170 kPa (358 25 psi)Pressure limiter setting (above charge pressure) ... 36500 1000 kPa (5300 145 psi)Actuation pressure for the crossover relief valve (above pressure limiter setting) ... 3450 kPa (500 psi)Note: The crossover relief valve pressure setting is not adjustable.System relief pressure ... 39900 1600 kPa (5800 230 psi)Note: The system relief pressure is the sum of the case pressure, charge pressure, relief setting, and setting for the pressure limiter valve. (A) Steering pump (B) The charge pumps consist of two charge pumps. One charge pump is shared by the steering hydraulic system and by the implement hydraulic system. The other charge pump is the transmission charge pump. (C) End section of the charge pump that is used for steering and implements (D) Drive end section of the transmission charge pumpDifferential Steering Pump
Illustration 2 g00289124
(1) Lubricate the pistons and the cylinder block prior to the assembly of the pistons. (2) Torque for one bolt ... 33 N m (24 lb ft) (3) Torque for one bolt ... 33 N m (24 lb ft) (4) Torque for three small 6.0 mm (.24 inch) end cap bolts ... 14 N m (10 lb ft) (5) Torque for six bolts (top and bottom in cover) ... 33 N m (24 lb ft) (6) Torque for two nuts ... 23 N m (17 lb ft) (7) Torque for two bolts (each side of cover) ... 24 N m (18 lb ft) (8) Torque for four bolts ... 14 N m (10 lb ft)
Illustration 3 g00289125
(9) Torque for four large end cap bolts ... 256 N m (189 lb ft)
Illustration 4 g00537700
(10) Torque for three bolts on the outside of each servo cylinder ... 24 N m (18 lb ft)Torque that is required to rotate the shaft after assembly Minimum torque ... 5 N m (4 lb ft) Maximum torque ... 10 N m (7 lb ft)The rotation of the pump is counterclockwise when the pump is viewed from the drive end.Type of pump: gerotor (piston)For the test, use SAE 10W oil at 65°C (150°F).Reference: See Systems Operation/Testing and Adjusting, "Pump Effeciency Check".Test at Rated Engine Speed Output ... 201 L/min (53 US gpm) Pump speed ... 2667 rpm Pressure ... 690 kPa (100 psi) Engine speed ... 2100 rpm Output ... 197 L/min (52 US gpm) Pump speed ... 2667 rpm Pressure ... 6900 kPa (1000 psi) Engine speed ... 2100 rpmTest at Half Engine Speed Output ... 100 L/min (26.4 US gpm) Pump Speed ... 1333 rpm Pressure ... 690 kPa (100 psi) Engine Speed ... 1050 rpm Output ... 98 L/min (26 US gpm) Pump Speed ... 1333 rpm Pressure ... 6900 kPa (1000 psi) Engine Speed ... 1050 rpm


Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.