AVSPARE.COM
parts catalog

NUT 1C3807 - Caterpillar



1C3807 NUT Caterpillar parts NUT
Rating:
86
Alternative (cross code) number:
CA1C3807
1C-3807
1C3807
Caterpillar 1C3807 NUT
Weight: 1 pounds 0 kg.

Buy NUT 1C3807 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Before lifting, be sure to fully retract all hydraulic cylinders. Secure the piston rod to the cylinder tube with a wire rope cable so the piston rod will not slide out during lifting work.
1. Base Machine - Use two boom linkage pin holes and the lifting eye provided on the swing frame. Install boom linkage pin (1) and protective sleeve (2) in each hole with bolt (3) and fasten a proper rated wire rope cable [approximately 5 m (16 ft 5 in) long] to linkage pin (1).To access the lifting eye on the rear of the swing frame, remove the center access cover on top of the engine compartment. Fasten a proper rated wire rope cable [approximately 6 m (19 ft 8 in) long] to the lifting eye with a shackle.Using an appropriate lifting device, tension the lifting cables to take up the mass and slowly lift the base machine. 2. Counterweight - Fasten a proper rated lifting wire rope cable with shackles to the lifting eye provided in each bracket on the counterweight. Lift the counterweight. 3. Cab - Install two lifting eye bolts (M16 × P2) in the corners, 180° apart, on the cab top and fasten proper rated wire rope cables to the lifting eyes with shackles. Lift the cab. 4. Stick with bucket cylinder - Use the two lifting eyes provided in the brackets on top of the stick. Install shackles through the lifting eyes and fasten proper rated wire rope cables to the shackles. Fasten a wire rope cable to the front section of the stick. It is recommended to use a cloth to protect the lifting cable from being damaged by the stick edges. Slowly lift the stick with the bucket cylinder as a set. 5. Bucket - Install bucket linkage pin (1) and protective sleeve (2) in the brackets of the bucket. Hold the linkage pin (1) in place with bolts (3) and nut (4). Fasten two proper rated wire rope cables to the linkage pin. Lift the bucket. 6. Boom with stick cylinder - Use the two lifting eyes provided in the brackets on top of the boom. Fasten two proper rated wire rope cables to the lifting eyes with shackles and secure the piston rod to the cylinder tube. Slowly lift the boom with the stick cylinder as a set. 7. Boom cylinder - Fasten two proper rated wire rope cables to the boom cylinder and secure the piston rod to the cylinder tube. Slowly lift the boom cylinder. 8. Walk way - Use two proper rated wire rope cables. Fasten the lifting cables to the positions indicated by the arrows. Lift the walk ways one at a time.Machine Loading onto a Trailer
Before you load the machine onto the trailer, remove ice, snow, or other slippery material from the loading dock and from the truck bed. This will prevent the machine from sliding while the machine is being loaded. This will also keep the machine from moving in transit.For


Parts nut Caterpillar catalog:

1B9972 NUT
Caterpillar
1B8083 NUT
Caterpillar
1B7019 NUT
Caterpillar
1B6033 NUT
Caterpillar
1C4252 NUT
Caterpillar
1C4297 NUT
Caterpillar
1C4350 NUT
Caterpillar
1C4676 NUT
Caterpillar
1C9470 NUT
Caterpillar
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.