AVSPARE.COM
parts catalog

NUT, 1/2-20 37 FLARE 7097889R1 - Caterpillar



7097889R1 NUT, 1/2-20 37 FLARE Caterpillar parts NUT
Rating:
26
Alternative (cross code) number:
CA7097889R1
70978-89R1
7097889R1
Caterpillar 7097889R1 NUT, 1/2-20 37 FLARE

Buy NUT, 1/2-20 37 FLARE 7097889R1 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 3
 
  For full view, you need register

Information:

Removal Procedure
Start By:
Turn the battery disconnect switch to the OFF position. Refer to Operation and Maintenance Manual, "Battery Disconnect Switch".
Put identification marks on all wires and all connectors for installation purposes.
Illustration 1 g00930171
Remove six bolts (2) in order to lower cab headliner (1) .
Illustration 2 g00930172
Disconnect harness (3) for dome light (4) and harness (5) for speakers (6) before removing cab headliner (1) from the cab.
Illustration 3 g00930173
Disconnect hose (7) for the windshield washer. Uncouple cap (8) for wiper arm (9) at connector (10). Open cap (11) and remove nut (12) and the washer in order to remove wiper arm (9) from the machine.
Illustration 4 g00930174
Illustration 5 g00930175
Disconnect electrical connector (13) for wiper motor (14). With the aid of a second person, support the wiper motor from the inside of the cab. At the same time remove nut (15), sealing washer (16), cap (17), nut (18) and sealing washer (19). Remove the wiper motor from the machine.Installation procedure
Clean all parts and inspect all parts. If any parts are worn or damaged, use new Caterpillar parts for replacement.
Illustration 6 g00930174
Illustration 7 g00930175
With the aid of a second person, position wiper motor (14) and install sealing washer (16), nut (15), sealing washer (19), nut (18) and cap (17). Tighten nut (18) to a torque of 7.5 .5 N m (5.5 0.4 lb ft). Connect electrical connector (13) .
Illustration 8 g00930172
Position cab headliner (1) in the cab in order to enable the connection of electrical connector (5) for speakers (6) and harness (3) for dome light (4) .
Illustration 9 g00930171
Lift cab headliner (1) into position and install six bolts (2).
Use the following procedure to install the wiper arm:
If a new wiper motor has been installed disregard steps 5.b and 5.c.
Turn the battery disconnect switch to the ON position. Refer to Operation and Maintenance Manual, "Battery Disconnect Swithch.".
Turn the switch for the front window wiper to the ON position and then turn the switch for the front window wiper to the OFF position. This will make sure that the wiper motor is in the PARK position. Refer to Operation and Maintenance Manual, "Window Wiper and Washer Control".
Illustration 10 g00930228
Illustration 11 g00930173
Couple cap (8) onto connector (10) for wiper arm (9). Position wiper arm (9) so that the wiper blade is in full contact with the front left side of the windshield. The wiper blade must be parallel with the edge of the windshield at a distance of 127 3 mm (5 0.1 inch). Note the black arrows on illustration 10. Install nut (12) and tighten the nut to a torque of 23 1 N m (17 0.7 lb ft).
Wait for at least thirty minutes. Do not wait for more than four hours. Tighten nuts (12) again to a torque of 23 1 N m (17 0.7 lb ft). Close cover (11) for the wiper arm.
Connect hose (7) for the window washer.


Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.