AVSPARE.COM
parts catalog

OPTION AR-REGIONAL 3534232 - Caterpillar



3534232 OPTION AR-REGIONAL Caterpillar parts 824H, 825H OPTION
Rating:
83
Alternative (cross code) number:
CA3534232
353-4232
3534232
Caterpillar 3534232 OPTION AR-REGIONAL

Buy OPTION AR-REGIONAL 3534232 Caterpillar genuine, new aftermarket tractor parts with delivery
SOIL COMPACTOR, WHEEL DOZER,

Compatible equipment models: 3534232:

SOIL COMPACTOR  825H  
WHEEL DOZER  824H   Caterpillar
  For full view, you need register

Information:


Install port plate (16).
Illustration 19 g00779279
Install washer set (15).
Illustration 20 g01018466
Improper assembly of parts that are spring loaded can cause bodily injury.To prevent possible injury, follow the established assembly procedure and wear protective equipment.
Install spring (12) and spool (13) into head (8). Install adapter (14) and the O-ring seal into head (8).
Illustration 21 g00779259
Install plugs (11) and the O-ring seals.
Illustration 22 g00779248
Lower the temperature of bearing (10) and install bearing (10).
Illustration 23 g00779238
Use a shim or shims (9) so that the following requirements are met. Note: During the following checks, turn the travel motor output shaft in a clockwise direction.
Illustration 24 g01018475
Use Tooling (G) in order to turn the output shaft. The travel motor output shaft does not rotate with an applied torque of 440 N m (325 lb ft) with the parking brake release port open.
Illustration 25 g01018476
Apply the air pressure at orifice (X). Use Tooling (G) in order to turn the output shaft when the parking brake release port is pressurized to 780 kPa (115 psi). Perform this procedure with the inlet port and the outlet port open to the hydraulic oil tank. The travel motor output shaft rotates with an applied torque of 29 N m (21 lb ft) or less. Note: It may be necessary to remove head (8) several times in order to determine the correct thickness of shim or shims (9) that are used to adjust the rolling torque of the travel motor output shaft.
Apply a thin layer of Tooling (H) on shim or shims (9). Install the shim or shims on the head. The grease will hold the shim or shims in place during the installation of the head. Install the head on the body of the travel motor.
Illustration 26 g01018464
To prevent possible damage to the travel motor, fill the unit with oil at least to the fill port before operating the machine. Refer to the Operation and Maintenance Manual for the correct oil specification.
Install O-ring seal (6) and O-ring seals (7). Install head (8 ). Install socket head bolts (5). Tighten bolts (5) to a torque of 177 18 N m (131 13 lb ft).
Illustration 27 g00779215
Install Tooling (A). Install traction control valve (3). Remove Tooling (A). Install six bolts (2). Tighten bolts (2) to a torque of 80 8 N m (59 6 lb ft).
Illustration 28 g00779163
Install traction control valve (3) and travel motor (4) into the final drive as a unit.
Illustration 29 g00779154
Install bolts (1). Tighten bolts (1) to a torque of 240 40 N m (177 30 lb ft). End By:
Install the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Install".

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts option Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.