AVSPARE.COM
parts catalog

OPTION AR-SERVICE 3534270 - Caterpillar



3534270 OPTION AR-SERVICE Caterpillar parts 993K OPTION
Rating:
68
Alternative (cross code) number:
CA3534270
353-4270
3534270
Caterpillar 3534270 OPTION AR-SERVICE

Buy OPTION AR-SERVICE 3534270 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL LOADER,

Compatible equipment models: 3534270:

WHEEL LOADER  993K   Caterpillar
  For full view, you need register

Information:

Removal Procedure
Use the same removal procedure for the front and rear seals.Reference: See table 2 and illustration 1.
Table 2
Required Tools    
Tool    Part Number    Part Description    Qty    
A     1U-7600     Slide Hammer Puller     1    
Illustration 1 g00997360
New seal (1) Seal (2) Wear sleeve (3) Wear sleeve flange
Use a hammer and a punch in order to puncture 3 or more holes into the wear sleeve (2) on the flange side of the wear sleeve (3). Use Tool (A) to remove the wear sleeve (2) .
Use a punch or Tool (A) to puncture a hole in seal (1). Use Tool (A) to remove seal (1) .Installation Procedure
Reference: See table 3 and illustrations 2, 3, and 4.
Table 3
Required Tools    
Tool    Part Number    Part Description    Qty    
A     5P-1733     Seal Locator     1    
B     5P-1737     Bolts     3    
C     9S-8858     Nut (Seal Installer)     1    
D     6V-6142     Front Seal Installer     1    
E     6V-6143     Rear Seal Installer     1    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: The seal and the wear sleeve must be replaced at the same time. Once the seal and the wear sleeve are separated, these components cannot be used again. Refer to Special Instruction, SMHS8508, "Special Handling Information and Installation Instructions for Crankshaft Seal Groups That Have Hydrodynamic Grooves In the Sealing Lip" before the seal is serviced.Note: Do not use any type of lubricant during the installation of the crankshaft seal and the wear sleeve.
The front and rear seals and wear sleeves have different spiral grooves in the seal. Because of this type of design, the front seal group for an engine is different from the rear seal group. If a seal group is installed on the wrong end of the engine, oil can actually be taken out of the engine instead of moving oil back into the engine.
Illustration 2 g00515623
Crankshaft seal installationNote: Install the seal with the directional arrow outward in order to show the direction of the crankshaft rotation.
Before installation of the crankshaft seal and the wear sleeve, inspect the crankshaft for scratches. Also, inspect the crankshaft for any distortion on the surface that may lead to an out of round condition. Use a polishing cloth in order to remove any imperfections on the crankshaft.
Use 4C-9500 Quick Cure Primer to clean the outside diameter of the crankshaft.Note: The new seal comes with the retaining compound that is already applied to the inside diameter of the wear sleeve.
Illustration 3 g00997376
New seal (1) Seal (2) Wear sleeve
Illustration 4 g00997146
Typical example
Fasten Tool (A) to the crankshaft with Tool (B) .
Position wear sleeve (2) and seal (1) on Tool (A). Install Tool (D) for the front seal, or Tool (E) for the rear seal, onto Tool (A) . Lubricate the face of the washer on Tool (C). Install Tool (C) on Tool (A)

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts option Caterpillar catalog:

3479819 OPTION AR-LINKAGE
345D L, 345D L VG, 349D, 349D L
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.