AVSPARE.COM
parts catalog

OPTION AR-CONVERSION 3534316 - Caterpillar



3534316 OPTION AR-CONVERSION Caterpillar parts 990H OPTION
Rating:
57
Alternative (cross code) number:
CA3534316
353-4316
3534316
Caterpillar 3534316 OPTION AR-CONVERSION

Buy OPTION AR-CONVERSION 3534316 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL LOADER,

Compatible equipment models: 3534316:

WHEEL LOADER  990H   Caterpillar
  For full view, you need register

Information:

Measuring Track Tension
1. Lay a straight edge long enough to reach from the idler wheel to the guide roller. 2. Measure the maximum amount of track sag from the high point of the track grouser to the bottom of the straight edge. Track properly adjusted will have approximately 40 to 50 mm (1 5/8 to 2 1/8 inches) slack.Tighten the Track
1. Add grease through the high pressure fitting until the correct track tension is reached.2. Operate the machine back and forth to equalize the pressure. 3. Recheck the amount of track sag and adjust as necessary.Loosen the Track
1. Loosen the high pressure fitting carefully (one turn maximum) until grease is allowed to emerge from the cylinder through the fitting.2. Retighten the high pressure fitting to 35 N m (23 lb ft) when the desired track tension is reached.Air Conditioner (If Equipped)
Checking the Amount of Refrigerant
1. Start the engine and move the governor control lever backward to the half way position. 2. Look at the sight glass on the receiver dryer and note the amount of refrigerant in accordance with the following. 3. In figure A, almost transparent with few bubbles which disappear as the engine rpm varies: this indicates a satisfactory amount of refrigerant.4. In figure B, a lot of bubbles are present: this indicates lack of refrigerant.5. In figure C, small amounts of vapor are present: this indicates almost no refrigerant.6. If figure B or C is noticed, consult your Caterpillar dealer for recharging.7. Operation of the air conditioner without correct amounts of refrigerant could cause failure of the compressor.Inspect and/or Adjust the Belt
An incorrectly tensioned V-belt could cause not only a decrease of the compressor performance but damage to the belt and compressor.
1. Measure the deflection of the belt.2. Apply approximately 98 N (22 lb) force midway between the pulleys. The belt should deflect 7 to 10 mm (0.3 to 0.4 inch).3. If the deflection is out of specification, adjust the belt with the adjusting bolt (1) of idler pulley assembly until the deflection is correct.Cleaning the Condenser
If excessively dirty, clean condenser with a brush. To prevent damage or bending of the fins, do not use a stiff brush.Repair the fins if found defective.
1. Unlatch and raise the engine hood.2. Remove the bolts, and washers. Open the radiator cover. 3. Wash off all dirt and dust from the condenser with clean water.Cleaning Filters
Pressure air can cause personal injury.When using pressure air for cleaning, wear a protective face shield, protective clothing and protective shoes.The maximum air pressure must be below 205 kPa (30 psi) for cleaning purposes.
1. Pull the cover knob out and take the front filter cover (1) and front filter (2) out.2. Pull the cover knob out and remove side filter cover (3) and side filter (4). 3. Clean filters and covers using pressure water 280 kPa (40 psi) or less, or compressed air. 4. Assemble front filter (2) into front cover (1), and assemble front filter cover (1) into the unit.5. Push in the

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts option Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.