parts catalog

OPTION AR-LINKAGE 3966771 - Caterpillar

3966771 OPTION AR-LINKAGE Caterpillar parts 314D LCR
Alternative (cross code) number:
Caterpillar 3966771 OPTION AR-LINKAGE

Buy OPTION AR-LINKAGE 3966771 Caterpillar genuine, new aftermarket tractor parts with delivery

Compatible equipment models: 3966771:

EXCAVATOR  314D LCR   Caterpillar
  For full view, you need register


Table 1
419-9827 C175 Damper Lifting Device Specifications    
Dimensions     262 x 511 mm (10.3 x 20.1 in)    
Material     Steel    
Working Load Limit (WLL)    
227 kg (500 lb)    
6 kg (13 lb)    Note: Refer to the appropriate Disassembly and Assembly Service Manual for mounting and lifting hardware and correct location of the lifting point.References
Table 2
KENR6052     Vibration Damper Remove and Install    
KENR8384     Vibration Damper Remove and Install    Note: Refer to SIS Web for updated materials. The list of references may change frequently. Always locate and refer to the appropriate Disassembly and Assembly Service Manual for information on mounting and lifting hardware. Operation Section
Personal injury or death can result from lifting a heavy component.The heavy component can fall if using an incorrect hoist and/or sling or fastener to lift the load.Be sure the hoist and other devices have the correct lifting capacity to lift a heavy component. The approximate weight of the heavy component is given below.
Failure to comply to the rated load can cause possible personal injury or attachment damage.Review the rated load of a particular attachment before performing any operation. Make adjustments to the rated load as necessary.
The C175 Damper Lifting Device weighs 6 kg (13 lb).
Identify the load and weight of the machine component to be lifted. Do not exceed the Working Load Limit (WLL) of 227 kg (500 lb).
Illustration 5 g03434178
Figure 1
Attach the device to the Vibration Damper as shown in Figure 1. Rotate the lever into the position shown to lock it into place.
Illustration 6 g03434188
Figure 2
Attach a suitable chain hoist to the device. Do not lift at any angle other than shown in the illustrations.
Illustration 7 g03434201
Figure 3
To avoid injury do not stand on or between implement and machine while operating lift control.
Slowly lift the Vibration Damper to the vertical position. Carefully observe the component to verify that shifting does not occur.Note: The WLL of the hoist or lifting device used for this step should be more than the weight of the machine component being lifted and all the tooling used to lift it.
Illustration 8 g03434211
Figure 4
Follow the information in the Disassembly and Assembly Service Manual.Inspection and Maintenance Section
Inspect tooling prior to each use for damage, bending, nicks, burrs, dents, cracks, bent or worn parts. If damage is found, destroy the tool and dispose of as scrap. Replace damaged tool with new product.
Do not use unless the Working Load Limit (WLL) identification markings are legible.
Do not use if any holes are elongated or deformed.
Illustration 9 g03434221
Do not use if hardware is damaged or missing.
Have the tool inspected annually by an approved dealership inspector.Cleaning
Clean the tooling using a non-solvent based cleaner.Storage
Store the tooling in a clean, dry location to prevent rust or corrosion. Tooling can be damaged by moisture or high humidity.
The tool should be stored in the most stable position.Tool Disposal
At the end of the operational life of the tool, destroy the tool and dispose of as scrap.

Parts option Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.