AVSPARE.COM
parts catalog

OPTION AR-LINKAGE 3966790 - Caterpillar



3966790 OPTION AR-LINKAGE Caterpillar parts 314D LCR OPTION
Rating:
37
Alternative (cross code) number:
CA3966790
396-6790
3966790
Caterpillar 3966790 OPTION AR-LINKAGE

Buy OPTION AR-LINKAGE 3966790 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Compatible equipment models: 3966790:

EXCAVATOR  314D LCR   Caterpillar
  For full view, you need register

Information:


Illustration 3 g01564895
Terminal locations at the P1 ECM connector for the speed control
(P1-1) Secondary throttle
(P1-66) Primary throttle
Illustration 4 g03285456
Terminal locations at the P2 ECM connector for the speed control
(P2-40) Analog throttle
Illustration 5 g03285458
Terminal locations at the engine interface connector for the speed control
(Terminal 15) Analog throttle for primary ECM
(Terminal 16) Analog throttle for secondary ECM
(Terminal 66) Primary throttle
(Terminal 68) Secondary throttle
Table 2
Troubleshooting Test Steps Values Results
1. Inspect the Electrical Connectors and the Wiring
A. Remove the electrical power from the ECM.
B. Thoroughly inspect connectors (1), (2), and (3). Inspect all of the connectors in the harness from the engine interface connector to the speed control that are associated with the circuit. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
C. Perform a 45 N (10 lb) pull test on each of the wires in the ECM connectors, the engine interface connector, and the connector for the EMCP that are associated with the circuit.
D. Check the torque of the allen head screws for each of the ECM connectors. Refer to Troubleshooting, "Electrical Connectors - Inspect" for the correct torque values.
E. Check the harness and the wiring for abrasion and for pinch points from the batteries to the ECM.
Connectors
Results: The connectors and wiring appear to be OK.
Proceed to Test Step 2
Results: The connectors and/or wiring are not OK.
Repair: Repair the wiring and/or the connectors. Replace parts, if necessary. Verify that the original problem has been resolved.
2. Check for Active Diagnostic Codes
A. Connect Caterpillar Electronic Technician (ET) to the service tool connector.
B. Restore the electrical power to the ECM.
C. Monitor the active diagnostic code screen on Cat ET. Check for an active 08 code for the throttle signal.
Note: Wait at least 30 seconds in order for the diagnostic codes to become active.
D. Remove the electrical power from the ECM.
Codes
Results: No diagnostic codes are active.
Repair: If the above code has been logged, there may be an intermittent problem in the harness or in a connector. Refer to Troubleshooting, "Electrical Connectors - Inspect" in order to troubleshoot intermittent electrical problems.
If a problem with the speed control circuit is suspected, proceed to Test Step 3
Results: A 08 diagnostic code is active at this time. The ECM has detected an erratic signal at the input for the throttle signal.
Proceed to Test Step 3
3. Check the Supply Voltage to the Speed Control
A. Restore the electrical power to the ECM.
B. Start the engine.
C. Measure the voltage between terminals +B and −B at the speed control.
D. Stop the engine. Remove the electrical power from the ECM.
24 3.0 VDC
Results: The engine started and the supply voltage is 24 3.0 VDC at the speed control. The speed control is receiving supply voltage.
Proceed to Test Step 4
Results: The supply voltage is not 24 3.0 VDC.
Repair: The supply voltage is not reaching the speed control. If the engine started, the control relay is receiving electrical power. There is a problem in the harness or the connectors between the output of control relay and the speed control. The problem may be in the ground

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts option Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.