AVSPARE.COM
parts catalog

PANEL GP-INSTRUMENT 1246618 - Caterpillar



1246618 PANEL GP-INSTRUMENT Caterpillar parts 3176B PANEL
Rating:
71
Alternative (cross code) number:
CA1246618
124-6618
1246618
Caterpillar 1246618 PANEL GP-INSTRUMENT

Buy PANEL GP-INSTRUMENT 1246618 Caterpillar genuine, new aftermarket tractor parts with delivery
INDUSTRIAL ENGINE,

Compatible equipment models: 1246618:

INDUSTRIAL ENGINE  3176B   Caterpillar
  For full view, you need register

Information:


Illustration 17 g03381740
Make sure that all the surfaces are clean and that all the surfaces are prepared for the installation of the brackets.Remove paint from the indicated areas. Refer to Illustration 17.
Illustration 18 g06309508
(7) 557-8556 Bracket As
(8) 512-9802 Plate
(9) 512-9801 Plate
(10) 512-9805 Bracket As
Place the brackets in the proper order. Refer to Illustration 18.
Illustration 19 g03381766
(A) 1515.0 3.0 mm (59.65 0.12 inch)
(B) 898.0 3.0 mm (35.35 0.12 inch)
(C) 576 1.5 mm (22.68 0.06 inch)
(D) 133 1 mm (5.24 0.04 inch)
(E) 133 1.5 mm (5.24 0.06 inch)
(F) 266 1.5 mm (10.47 0.06 inch)
(G) 351 1.5 mm (13.82 0.06 inch)
(H) 277.5 1.5 mm (10.93 0.06 inch)
(J) 886.5 3.0 mm (34.90151 0.11811 inch)
(K) 110 1 mm (4.33 0.04 inch)
(L) 110 1 mm (4.33 0.04 inch)
Illustration 20 g03381975
Section B-B
(M) 625.0 mm (24.61 inch)
(N) 103.0 1.5 mm (4.06 0.06 inch)
(P) 6.2 1.5 mm (0.24 0.06 inch)
(R) 828.0 mm (32.60 inch)
(S) 291.8 1.5 mm (11.49 0.06 inch)
(T) 267.0 1.5 mm (10.51 0.06 inch)
Illustration 21 g03381978
Section A-A
(U) 726.0 mm (28.58 inch)
(V) 755.0 mm (29.72 inch)
Use a 6 mm (0.25 inch) fillet weld with 1.5 mm (0.06 inch) root penetration to secure brackets to the top and back of the bucket. Refer to the dimensions in Illustration 19, Illustration 20, and Illustration21.
Dress grind all of the welds. Paint the welds and any exposed surfaces of the metal. Use Caterpillar yellow primer and Caterpillar yellow paint.
Illustration 22 g06309419
(6) 8T-4159 Bumper
(13) 5C-7261 Nut
(15) 8T-4122 Hard Washer
(16) 8T-4224 Hard Washer
Assemble to bump stops to the rear of the bucket. Refer to Illustration 22.
Illustration 23 g06309516
(3) 112-1776 Pin As
(4) 104-6316 Pin
(11) 423-4990 Bracket As
(12) 4J-1888 Cotter Pin
Install two bracket assemblies (11) to the bucket using pin (4) and cotter pin (12). Lock the assemblies into place with two-pin assemblies (3).
Illustration 24 g06310544
(1) 452-7707 Fork
(2) 104-6317 Pin
(3) 112-1776 Pin As
(5) 5D-8159 Pin As
(14) 6V-8144 Retaining Ring
(17) 9R-0109 Washer
Install the forks (1) onto the bracket assemblies. Use one pin (2), two washers (17) , and two retaining rings (14) on each side.
Secure the forks using two pin assemblies (3) and two pin assemblies (5).

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts panel Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.