AVSPARE.COM
parts catalog

PANEL GP-INSTRUMENT 2333280 - Caterpillar



2333280 PANEL GP-INSTRUMENT Caterpillar parts 14M, 16M PANEL
Rating:
64
Alternative (cross code) number:
CA2333280
233-3280
2333280
Caterpillar 2333280 PANEL GP-INSTRUMENT
Weight: 11 pounds 5 kg.

Buy PANEL GP-INSTRUMENT 2333280 Caterpillar genuine, new aftermarket tractor parts with delivery
MOTOR GRADER,

Compatible equipment models: 2333280:

MOTOR GRADER  14M   16M   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:

Note: Either Tooling (C) can be used. Use the Tooling that is most suitable.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Do not turn the crankshaft while the valve springs are removed.
Plug the apertures for the push rods in the cylinder head to prevent the entry of loose parts into the engine.
Illustration 3 g01335931
Inspect valve springs (11) for damage and for the correct length. Refer to Specifications, "Cylinder Head Valves" for the correct procedure.
If necessary, install a new valve stem seal onto the valve guide.Note: The outer face of the valve guide must be clean and dry before installing the valve stem seal.
Install valve spring (11) onto the cylinder head. Position valve spring retainer (10) on valve spring (11).
Improper assembly of parts that are spring loaded can cause bodily injury.To prevent possible injury, follow the established assembly procedure and wear protective equipment.
Ensure that the valve spring is compressed squarely or damage to the valve stem may occur.
Install Tooling (B) in the appropriate position on the cylinder head to compress valve spring (11).
Apply sufficient pressure to Tooling (B) to install valve keepers (9).Note: Do not compress the spring so that valve spring retainer (10) touches the valve stem seal.Install the valve spring keepers.
Carefully release the pressure on Tooling (B).
Repeat steps 2 to 6 for the remaining valves.
The valve spring keepers can be thrown from the valve when the valve spring compressor is released. Ensure that the valve spring keepers are properly installed on the valve stem. To help prevent personal injury, keep away from the front of the valve spring keepers and valve springs during the installation of the valves.
Remove Tooling (B).
Use Tooling (C) to rotate the crankshaft through approximately 45 degrees. Rotate the crankshaft through approximately 45 degrees will ensure that the appropriate valve is clear of the piston. Lightly strike the top of the valve with a soft hammer to ensure that valve keepers (9) are properly installed.Note: If all valve springs require replacement the procedure can be carried out on two cylinders at the same time. The procedure can be carried out on the following cylinders. 1 and 6, 2 and 5 and 3 and 4. Remember that the crankshaft must not be turned while the valve springs are removed. Ensure that all the valve springs are installed before changing from one pair of cylinders to the other pair of cylinders. If all valve springs do not require replacement, the springs must be replaced in pairs.
Illustration 4 g01335929
Follow Steps 10.a through 10.g to install the harness assemblies for the electronic unit injectors.
Ensure that harness assembly (4) for the electronic unit injectors and the bore in valve mechanism cover base (8) are clean and free from damage. Replace any damaged components.
Use Tooling (D) to lubricate a new O-ring seal. Install new O-ring seal (6) onto harness assembly (4) for the electronic unit injectors.
Install harness assembly (4) into valve mechanism cover base (8) from inside the valve mechanism cover base.
Use Tooling (A) to install circlip

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
16M Motor Grader B9H00001-UP (MACHINE) POWERED BY C13 Engine
14M Motor Grader B9J00001-UP (MACHINE) POWERED BY C11 Engine
14M Motor Grader R9J00001-UP (MACHINE) POWERED BY C11 Engine
16M Motor Grader R9H00001-UP (MACHINE) POWERED BY C13 Engine


Parts panel Caterpillar catalog:

2658947 PANEL AS
140M, 14M, 160M
2658948 PANEL AS
140M, 14M, 160M
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.