AVSPARE.COM
parts catalog

PANEL GP-INSTRUMENT 3534756 - Caterpillar



3534756 PANEL GP-INSTRUMENT Caterpillar parts C13, C15, C18, C9.3, CX31-C13I, CX31-C18I PANEL
Rating:
9
Alternative (cross code) number:
CA3534756
353-4756
3534756
Caterpillar 3534756 PANEL GP-INSTRUMENT

Buy PANEL GP-INSTRUMENT 3534756 Caterpillar genuine, new aftermarket tractor parts with delivery
INDUSTRIAL ENGINE, PETROLEUM PACKAGE,

Compatible equipment models: 3534756:

INDUSTRIAL ENGINE  C13   C15   C18   C9.3  
PETROLEUM PACKAGE  CX31-C13I   CX31-C18I   Caterpillar
Number on catalog scheme: 4
 
  For full view, you need register

Information:


Illustration 49 g03662137
Make a 12 mm (0.47 inch) Bevel Groove weld from (B) to (C) .
Weld a 10 mm (0.39 inch) 3-pass Bevel-Groove from (A) to (B) .
Weld (A) to (D) using 6 mm (0.24 inch) weld. Use the back step welding method, stepping every 300 mm (11.8 inch). Alternate sides after every step, and skip where the spacer blocks currently are. Weld a 6 mm (0.24 inch) fillet weld down the remaining length of the bowl floor to the bowl side.
With the floor blocked, remove the rigging devices.
Cut off the locator blocks (16), and repair gouging to the bowl sides. Then finish welding the top of the floor using a 6 mm (0.24 inch) weld.
Illustration 50 g03653286
Using the back step method, stepping every 300 mm (11.8 inch). Alternate sides after every step, weld both sides of the bottom side of the floor to the bowl sides using a 6 mm (0.24 inch) fillet weld. Weld the bottom from (E) to (F) .
Illustration 51 g03653322
Weld in the additional cutting edge plates (2) on the left side and (3) on the right side. For both plates use an 8 mm (0.32 inch) fillet across the floor and down the cutting edge from location (G) to (H). Then on the outside, place a 12 mm (0.47 inch) 3-pass fillet from (J) to (K) .
Illustration 52 g03653336
Weld the end of the floor to the bowl side using a 6 mm (0.24 inch) fillet weld. Extend the weld from (L) to (M) on both sides of the bowl.
Illustration 53 g03653363
Locate plate (14) to the bottom of the push frame. Butt one edge of the plate against the new bottom assembly and locate the other edge as shown in the illustration. Tack weld plate (14) to the bottom of the push frame.
Illustration 54 g03653393
Left side of the machineView of the top side of the push frame
Finish weld the top side of plate (14) of the push frame to bottom assembly (1) using a 6 mm (0.24 inch) flare bevel groove weld. Weld the plate on two edges.
Illustration 55 g03653397
View of the bottom side of the push frame.
Finish weld plate (14) from location (N) to (P) using a 5 mm (0.2 inch) fillet welds.
Illustration 56 g03653405
The left side push frame
On the left side push frame tack on the following parts in the specified order. Tack on plate (6), plate (15), plate (9), plate (11), and plate (7) .
The right side push frame is not shown but is a mirror image of the figure above. On the right side push frame tack on the following parts in the specified order. Tack on plate (4), plate (15), plate (4), plate (5), plate (8), and plate (10) .
Illustration 57 g03653411
Weld out the push frame parts. Weld paths in red that are marked with (R) using a 6 mm (0.24 inch) fillet/groove. The weld paths in black are marked with an (S) using a 5 mm (0.2 inch) fillet/groove.
Illustration 58 g03653414
(T) 59 mm (2.3 inch)
Weld in gusset (12), and gusset (13). Maintain a distance of dimension (T) for

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
CX38-P892-C18I Petroleum Power Train Package A3X00001-UP POWERED BY C18 Industrial Engine
CX35-P800_C18I Petroleum Power Train Package BDN00001-UP
C15 Industrial Engine LDN00001-UP
C18 Industrial Engine BDN00001-UP
C9 Industrial Engine C9N00001-UP
C13 Industrial Engine KWJ00001-UP
CX31-P600-C13I Petroleum Power Train Package KWJ00001-UP
CX31-P600-C18I Petroleum Power Train Package BDN00001-UP
CX31-P600-C9I Petroleum Package C9N00001-UP


Parts panel Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.