AVSPARE.COM
parts catalog

PIN AS 1246528 - Caterpillar



1246528 PIN AS Caterpillar parts 350 L, 5080 PIN
Rating:
21
Alternative (cross code) number:
CA1246528
124-6528
1246528
Caterpillar 1246528 PIN AS
Weight: 78 pounds 35 kg.

Buy PIN AS 1246528 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR, FRONT SHOVEL,

Compatible equipment models: 1246528:

EXCAVATOR  350 L  
FRONT SHOVEL  5080   Caterpillar
Number on catalog scheme: 11
 
  For full view, you need register

Information:

Introduction
The following procedure is used in order to check the elongation of the drive chains.It is important to check the chains inside the tandem drives for wear. Normal operation will cause the pins, links, and rollers in the chains to wear. The chart lists the maximum limits of chain wear for a given number of chain links. Elongation of the chain due to wear is considered normal. Elongation of 3% is normal for all motor graders. The chain should be replaced when the chain reaches the maximum allowable wear. This action will prevent possible damage that could be caused by a broken chain.Note: A broken chain can wedge in the tandem housing. A wedged chain can damage the following items: sprockets, spindles and housings.Machine Preparation
Reference: Refer to the Power Train Disassembly and Assembly, "Drive Chain - Remove".
Remove the Drive Chain from the motor grader. Test Procedure
Inspect the chains. Replace the chains for the following conditions:
Cracks
Broken components
DeformationNote: If the chain does not pass the inspection, the entire chain must be replaced. Always replace both chains in a tandem housing at the same time. Do not splice a new section of chain on a worn section of chain. Worn chains will not engage the sprockets properly and increased damage to the sprocket may occur.
Personal injury or death can result from improper lifting or blocking.When a hoist or jack is used to lift any part or component, stand clear of the area. Be sure the hoist or jack has the correct capacity to lift a component. Install blocks or stands before performance of any work under a heavy component.Approximate weights of the components are shown. Clean all surfaces where parts are to be installed.
Suspend the chain from the hoist.
Hang a suitable scale from the chain. The scale must be able to measure the chain tension that is listed in Table 1.
Fix the free end of the scale to the motor grader. Reference: Refer to the Operation and Maintenance Manual , "Lifting and Tying Down the Machine" for the proper lifting locations for a motor grader.
Apply the proper amount of chain tension. Refer to Table 1. Ensure that all of the slack is out of the chain before a measurement is taken.
Measure the number of chain links that are listed in Table 1.
The elongation of the chain must be less than the specification in Table 1. Note: If the elongation of the chain is not within specifications, the chain must be replaced. Replace the entire chain. Always replace both chains in a tandem housing at the same time. Do not splice a new section of chain on a worn section of chain. Worn chains will not engage the sprockets properly and increased damage to the sprocket may occur.
You may reuse the old chain if the chain passed the checks for chain wear. Otherwise install a new chain. Reference: Refer to the Power Train Disassembly and Assembly, "Drive Chain - Install".Refer to the following table for the limits for chain wear.
Table 1
Limits

Caterpillar parts catalog:

Caterpillar parts catalog
350 L Excavator Custom Attachments 9FL00001-UP (MACHINE)


Parts pin Caterpillar catalog:

6V8236 PIN-SPRING
303, 311, 311B, 311C, 311D LRR, 312, 312B, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315D L, 318C, 318D L, 319C, 319D, 319D L, 319D LN, 320, 320 L, 320B, 320B FM LL, 320C, 320C FM, 32...
9S1315 PIN-CLEVIS
120, 120B, 140, 140B, 14E, 215, 227, 235, 245, 245B, 322B LN, 325 L, 325B L, 330B L, 350, 365B, 365B II, 375, 385B, 416B, 416C, 416D, 420D, 424D, 426B, 426C, 428, 428D, 430D, 436C, 446B, 5080, 5130, 5...
0998111 PIN-SPRING
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 307, 307B, 322, 322 FM L, 322 LN, 322B L, 322B LN, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 324E, 324E L, 324E LN, 325, ...
4I4814 PIN AS
318B, 318C, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320D, 320E LN, 320N, 322B LN, 323D L, 323D LN, 323D SA, 323D2 L, 323E L, 345B II, 345B L, 5080
1218702 PIN AS
325B L, 325C FM, 325D FM, 325D FM LL, 330B L, 330C, 330C FM, 330C L, 330D FM, 330D L, 330D LN, 336D L, 350, 350 L, 365B, 365B II, 365B L, 365C, 365C L, 385C, 568 FM LL, M325B, M325C MH, M325D L MH
1066838 PIN AS
350, 350 L, 365B, 375, 375 L, 5080
7Y2349 PIN
320 L, 320B, 320C, 320N, 325, 325 LN, 325B, 325B L, 325C, 325D L, 330, 330 FM L, 330C, 330D L, 345B II, 345B L, 345C L, 350, 350 L, 365B, 365B II, 365C, 365C L, 375, 385B, 385C L, 5080, TK1051
7Y3587 PIN
375, 375 L, 5080
5I3301 PIN AS
330, 330 FM L, 330 L, 330B, 330B L, 330C FM, 330D FM, 345B II, 345B L, 345C, 350 L, W330B
4I7062 PIN AS
375, 375 L, 5080
4I4922 PIN AS
375, 375 L, 5080
1066838 PIN AS
350, 350 L, 365B, 375, 375 L, 5080
1235342 PIN AS
345B II, 345B L, 350, 350 L, 365B, 365B II, 365C, 365C L, 375, 385B, 385C L, 5080
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.