parts catalog

PIN AS-YM 3967273 - Caterpillar

3967273 PIN AS-YM Caterpillar parts PIN
Alternative (cross code) number:
Caterpillar 3967273 PIN AS-YM
Weight: 26 pounds 11 kg.

Buy PIN AS-YM 3967273 Caterpillar genuine, new aftermarket tractor parts with delivery

Related part:
7V6716  PIN AS-YM  3967273  CL
  For full view, you need register


A top end overhaul involves the removal, the inspection, and the rework of the cylinder head components. Some additional components are replaced and serviced.Your Cat dealer can provide these services and components. Your Cat dealer can ensure that the components are operating within the appropriate specifications.Note: The driven equipment may also require service when the engine is overhauled. Refer to the literature that is provided by the OEM of the driven equipment.If you elect to perform an overhaul without the services of a Cat dealer, be aware of the following recommendations.Fuel Consumption Before A Top End Overhaul
The overhaul interval that is listed in this Operation and Maintenance Manual, "Maintenance Interval Schedule" is expressed in service hours. A more accurate figure to use is fuel consumption. Fuel consumption corresponds more accurately to the engine load. Table 1 lists an average range of fuel consumption for a reasonable load factor before a top end overhaul.
Table 1
Approximate Fuel Consumption Before A Top End Overhaul
Engine Model Fuel Consumption
C280-16 15160000 L (4005272 US gal) Remanufacturing or Rebuilding of Components
Rework the following components:
Air shutoff valve
Cylinder heads
Cylinder dowels
Exhaust valves
Exhaust valve seat inserts
Inlet valves
Inlet valve seat inserts
Inner valve springs
Outer valve springs
Unit injectors
Valve spring guides
Valve spring locks
Valve rotatorsNote: The angles of the valves and seats are different.If the valves and seats are not replaced, lap the valves and seats. The valve and the outer diameter of the seat must have 360 degrees of contact. If the valves and the seats require regrinding, see the Service Manual, "Specifications" module for the angles.Inspection and/or Replacement of Components
Inspect the following components according to the instructions that are in Caterpillar reusability publications. Refer to Guidelines for Reusable Parts and Salvage Operations, SEBF8029, "Index of Publications on Reusability or Salvage of Used Parts". Replace the components, if necessary.
Cylinder sleeves
Exhaust shields
Starting motor
ThermocouplesReplacement of Components
Replace the following components.
Connecting rod bearings
Cylinder head gaskets and seals
Exhaust manifold gaskets
Fuel transfer pump seals
Inlet air line seals
Oil cooler seals
Oil pump bearings and seals
Oil temperature regulators and seals
Turbocharger bearings, bushings, and seals
Valve lubricator pump (if equipped)
Water pump bearings and seals
Water temperature regulators and sealsCleaning and Inspection of Components
Clean the following components. Inspect the components for good condition. Replace the components, if necessary.
Oil cooler core
Oil suction screenOil Cooler Core
For cleaning the oil cooler core, see this Operation and Maintenance Manual, "Aftercooler Core - Clean/Test" procedure. The procedure may be used for cleaning both the aftercooler core and the oil cooler core.Oil Suction Screen
For cleaning the oil suction screen, see this Operation and Maintenance Manual, "Engine Oil - Change" procedure.

Parts pin Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.