AVSPARE.COM
parts catalog

PLATE AS 1246932 - Caterpillar



1246932 PLATE AS Caterpillar parts 515, 525 PLATE
Rating:
51
Alternative (cross code) number:
CA1246932
124-6932
1246932
Caterpillar 1246932 PLATE AS
Weight: 0.15 pounds 0 kg.

Buy PLATE AS 1246932 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL SKIDDER,

Compatible equipment models: 1246932:

WHEEL SKIDDER  515   525   Caterpillar
Number on catalog scheme: 22
 
  For full view, you need register

Information:


Illustration 1 g01272128
Connections of "Auxiliary Lever 2" position sensor
This diagnostic code is associated with the "auxiliary lever 2" position sensor. The position sensor is located in the "auxiliary control pod" attachment. The FMI 08 means that the Implement ECM 2 has determined that the signal frequency of the sensor or the signal pulse width is not within the expected range.The Implement ECM 2 communicates this condition to the Implement ECM over the SAE J1939 Data Link and the Implement ECM will activate this diagnostic code.The position sensor is a PWM sensor that operates at a frequency of approximately 500 100 Hz. The position sensor sends a PWM input signal to the Implement ECM 2. The duty cycle of the signal will vary from approximately 10% when the lever is in full rearward position to approximately 90% when the lever is in full forward position. When the lever is in the center position, the duty cycle will be approximately 50%. The possible causes of this diagnostic code are listed below:
The sensor has failed or a mechanical connection has failed.
Intermittent connections or poor connections
The ECM has failed. This is unlikely.Before performing this procedure, inspect the harness connectors that are involved in the circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all connections in the circuit are clean, that all connections are secure and that all connections are in good condition. If a problem with a connection is found, correct the problem and verify that this diagnostic code is active before performing this procedure. Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear the diagnostic codes when the problem has been corrected.Test Step 1. CHECK THE DUTY CYCLE AND THE SIGNAL FREQUENCY AT THE SENSORTurn the key start switch and the disconnect switch to the OFF position.
At the machine harness connector J1 for the "auxiliary control pod", use a 151-6320 Removal Tool to remove the signal wire U707-BU(Blue) and the socket at contact J1-7 from the harness connector. The machine harness connector J1 remains connected to the "auxiliary control pod".
Turn the disconnect switch and the key start switch to the ON position.
At the connector J1 for the auxiliary control pod, insert a 7X-1710 Multimeter Probe along the sensor return contact J1-3 (wire A295-BK(Black)).
Use the other multimeter probe to make contact through the harness connector with the "position sensor signal pin 7" on the connector for the control pod.
With the auxiliary lever stationary, measure the frequency of the signal from the sensor.
Measure the duty cycle of the sensor signal between the "auxiliary control pod" connector contacts J1-2 and J1-7. Slowly move the lever to the full rearward position and observe the duty cycle of the sensor signal. Slowly move the lever to the full forward position and observe the duty cycle of the sensor signal. Expected Result:The frequency

Caterpillar parts catalog:

Caterpillar parts catalog
525 Wheel Skidder 1DN00001-02253 (MACHINE) POWERED BY 3304 Engine
515 Wheel Skidder 4LR00001-UP (MACHINE) POWERED BY 3304 Engine


Parts plate Caterpillar catalog:

7C6672 PLATE-CLAMP
120H, 120H ES, 120H NA, 12H, 135H, 135H NA, 214B, 30/30, 3114, 3116, 3126, 3126B, 3126E, 3176, 3176B, 320 L, 320B, 322 FM L, 322 LN, 322B L, 322B LN, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, ...
8N4960 PLATE-THRUST
120B, 120G, 12G, 12H, 12H ES, 12H NA, 130G, 140B, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 1673C, 225, 229, 235, 235B, 235C, 235D, 330, 330 L, 3304, 3304...
3G5980 PLATE
153, 416, 416B, 426B, 428, 428B, 438B, 446, 446B, 446D, 508, 515, 518, 518C, 525, 525B, 525C, 528, 535B, 535C, 539, 545, 545C, 814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 824C, 826C, 916,...
6H5139 PLATE-PRESSURE
120G, 12F, 12G, 130G, 140, 141, 14E, 14G, 153, 16, 163, 16G, 172, 173B, 183, 183B, 184, 191, 193, 30/30, 416, 416B, 426B, 428, 428B, 438B, 446, 46, 508, 515, 517, 518, 525, 525D, 527, 528, 535D, 545D,...
9T7759 PLATE-RETAINING
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12K, 135H, 135H NA, 140H, 140K, 140K 2, 160H, 160K, 446B, 5130, 5130B, 515, 5230B, 525, 525B, 525C, 535B, 535C, 950G, 950G II, 950H, 950K, 962G, 962G I...
6E6604 PLATE-SPACER
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12K, 135H, 135H NA, 140H, 140K, 140K 2, 160H, 160K, 446B, 446D, 5130, 5130B, 515, 5230B, 525, 525B, 525C, 535B, 535C, 545, 545C, 950G, 950G II, 950H, 9...
6E6605 PLATE-LIMITER
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12K, 135H, 135H NA, 140H, 140K, 140K 2, 160H, 160K, 446B, 446D, 5130, 5130B, 515, 5230B, 525, 525B, 525C, 535B, 535C, 545, 545C, 950G, 950G II, 950H, 9...
4S6417 PLATE-THRUST
120G, 130G, 215B, 225, 3304, 3304B, 515, 517, 518C, 525, 527, 920, 936F, 941, 950, 951B, 955H, D320A, D330A, D4D, D4E, D4E SR, D4H, D4H XL, D4HTSK III, D5H, D5H XL, D5HTSK II, G3304, G3304B
7N8021 PLATE-BLOCK
120G, 130G, 215B, 3304, 3304B, 515, 517, 518C, 525, 527, 920, 936F, 950B, 951B, 955L, 963, D4E SR, D4H, D4H XL, D4HTSK III, D5H, D5H XL, D5HTSK II, G3304, G3304B
4N6863 PLATE AS-BACKING
120G, 130G, 215, 215B, 224, 225, 229D, 3304, 3304B, 515, 518, 518C, 525, 527, 926, 930, 936F, 950, 950B, 953, 963, CB-534, CS-643, D4E, D4E SR, D4H, D4H XL, D4HTSK III, D5H, D5H XL, D5HTSK II, G3508
6Y5632 PLATE-CLUTCH
120H, 515, 525, 525B, 525C, 535B, 535C, 545, 545C, 928F, 938F, 938G, 938G II, 938H, 966K, 966M XE, 972M XE, IT28F, IT38F, IT38G, IT38G II, IT38H
6K2707 PLATE-LOCK
515, 518, 518C, 525, 916, 918F, 920, 924F, IT18B, IT18F, IT24F
1242934 PLATE
515, 525, 525B, 535B, 545
1529081 PLATE
515, 525, 525B, 535B, 545
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.