AVSPARE.COM
parts catalog

PLATE 1247017 - Caterpillar



1247017 PLATE Caterpillar parts CW-14, PS-150B, PS-150C, PS-200B PLATE
Rating:
79
Alternative (cross code) number:
CA1247017
124-7017
1247017
Caterpillar 1247017 PLATE
Weight: 0.80 pounds 0 kg.

Buy PLATE 1247017 Caterpillar genuine, new aftermarket tractor parts with delivery
PNEUMATIC COMPACTOR,

Compatible equipment models: 1247017:

PNEUMATIC COMPACTOR  CW-14   PS-150B   PS-150C   PS-200B   Caterpillar
Number on catalog scheme: 3
 
  For full view, you need register

Information:

43. Remove bolts (49) from cage assembly. Fasten a hoist and remove cage assembly (50) from housing. Weight of cage assembly is 21 kg (46 lb).Assemble Swing Drive
1. Install O-ring seal (51) on cage assembly.2. Fasten a hoist and put cage assembly (50) on housing and install bolts.3. Install seal (52) on housing. 4. Lower the temperature of bearing cup (48) and install in cage assembly.5. Turn the housing over. Lower the temperature of bearing cups (46), (45) and (47). Install cups in housing.6. Put shaft (29) in position as shown.7. Heat bearing cone (43) to a maximum temperature of 135°C (275°F). Put the bearing cone in position on shaft.
Do not install bearing cone (43) on the shaft more than 127.0 mm (five in) from end of shaft. The bearing cone will be pushed into the correct position when the pinion gear is installed.
8. Install O-ring seal (43) on retainer (41). 9. Install Duo-Cone seal in each retainer with tool (A). The rubber seals and all surfaces that make contact with the seals must be clean and dry. After installation of seals, put oil on the contact surfaces of the metal seals.10. Install retainer on shaft.11. Install spacer (38) in retainer with notches in spacer toward Duo-Cone seal.12. Install O-ring (39) in retainer. Install retainer (37) on shaft.13. Put 5P3931 Anti-Seize Compound on the shaft and pinion gear splines. Put pinion gear (35) in position on end of shaft with hole in pinion gear in alignment with dowel in retainer (37). 14. Push the pinion gear into position on the shaft with tooling (B). The pinion gear is in the correct position when the retainer (34) is against the end of the shaft.15. Install O-ring seal (36), retainer (34) and bolt.16. Put shaft in position on tool (F). Fasten a hoist to housing and put it in position over shaft and on tooling (C).17. Install a 5/8 in - 11 NC forged eyebolt in shaft. Fasten a hoist and lift the shaft into position into housing. Make sure dowel in retainer (41) goes into hole in cage assembly.18. Put a floor jack under pinion and output shaft as a support. Remove hoist and eyebolt from shaft.19. Heat the two bearing cones for gear (27) in oil to a maximum temperature of 135°C (275°F). Put the bearing cones on the gear. Make sure the bearing cones are tight against the gear when installed.20. Put gear (27) in position in housing.21. Put 5P3931 Anti-Seize Compound on the shaft and splines in gear (26).22. Fasten a hoist and put gear (26) in position on shaft.23. Install retainer (24) and three 5/81/4 in - 11 NC bolts 3 in. long. Push the gear (26) on the output shaft with the bolts. Remove the longer bolts and install the original bolts. Do not push the gear (26) completely on the output shaft before the bolt in pinion is tightened.24. Install a 5/8 in - 11 NC forged eyebolt in the housing. Install a

Caterpillar parts catalog:

Caterpillar parts catalog
PS-150B Pneumatic Compactor 3XR00001-UP (MACHINE) POWERED BY 3054 Engine
PS-200B Pneumatic Compactor 5JR00001-UP (MACHINE) POWERED BY 3054 Engine
PS-150C Pneumatic Compactor FPS00001-UP (MACHINE) POWERED BY 3054T Engine
CW14 Pneumatic Compactor LTJ00001-UP (MACHINE) POWERED BY C3.4B Engine
PS-150C Pneumatic Compactor - Military NPK00001-UP (MACHINE)


Parts plate Caterpillar catalog:

6H5139 PLATE-PRESSURE
120G, 12F, 12G, 130G, 140, 141, 14E, 14G, 153, 16, 163, 16G, 172, 173B, 183, 183B, 184, 191, 193, 30/30, 416, 416B, 426B, 428, 428B, 438B, 446, 46, 508, 515, 517, 518, 525, 525D, 527, 528, 535D, 545D,...
4V0969 PLATE AS
10-20B, 30/30, 311D LRR, 312D, 314D LCR, 314E LCR, 315D L, 320D, 320D LRR, 321D LCR, 324E L, 324E LN, 328D LCR, 336D L, 336E L, 336F L, 345D L, 349E L, 349E L VG, 374D L, 390D L, 446B, 446D, 450E, 450...
7R7944 PLATE AS
10-20B, 30/30, 8-16B, AP-1000B, AP-900B, BG-225C, BG-2455C, BG-245C, CB-334D, CB-335D, CB-434B, CB-434C, CB-534B, CB-534C, CB-634, CB-634C, CP-433C, CS-323C, CS-431C, CS-531D, CS-533D, CS-563C, CS-563...
1261409 PLATE-RETAINING
914G, 939C, 953C, 963C, D4C III, D5C III, IT14G, IT14G2, PF-290B, PS-150B, PS-150C, PS-200B, PS-360B, PS-360C
1280997 PLATE
CW-14, PS-150B, PS-150C, PS-200B
1503029 PLATE
CW-14, PS-150B, PS-150C, PS-200B
1234604 PLATE AS
PS-150B, PS-200B
1249783 PLATE AS
CW-14, PS-150B, PS-150C, PS-200B
1502958 PLATE
CW-14, PS-150B, PS-150C, PS-200B
1389449 PLATE
PS-150B, PS-200B
1503029 PLATE
CW-14, PS-150B, PS-150C, PS-200B
1384284 PLATE
PS-150B, PS-200B
1374929 PLATE
PS-150B, PS-200B
1280997 PLATE
CW-14, PS-150B, PS-150C, PS-200B
1745648 PLATE
CW-14, PS-150B, PS-150C, PS-200B
1742368 PLATE
PS-150B, PS-200B
1708242 PLATE
CW-14, PS-150B, PS-150C, PS-200B
1670027 PLATE AS
CW-14, PS-150B, PS-150C, PS-200B
1381733 PLATE AS
CW-14, PS-150B, PS-150C, PS-200B
1365869 PLATE AS
CW-14, PS-150B, PS-150C, PS-200B
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.