AVSPARE.COM
parts catalog

PLATE 1247351 - Caterpillar



1247351 PLATE Caterpillar parts 10 FT, 10-20B, 10B, 8 FT, 8-16B, AP-655C, BG-2455C, BG-245C PLATE
Rating:
70
Alternative (cross code) number:
CA1247351
124-7351
1247351
Caterpillar 1247351 PLATE
Weight: 0.100 pounds 0 kg.

Buy PLATE 1247351 Caterpillar genuine, new aftermarket tractor parts with delivery
ASPHALT PAVER, ASPHALT SCREED,

Compatible equipment models: 1247351:

ASPHALT PAVER  AP-655C   BG-2455C   BG-245C  
ASPHALT SCREED  10 FT   10-20B   10B   8 FT   8-16B   Caterpillar
Number on catalog scheme: 24
 
  For full view, you need register

Information:


Illustration 1 g03200337
(A) through (J) are weld start points or weld stop points
(1) Adapter
(2) Base edge
Illustration 2 g03202141
Stagger all weld starts and weld stops
(1st) through (6th) represent weld passes
(1) Adapter
(2) Base edge
(3) Adapter to base edge weld
(K) 12 3 mm (0.5 0.12 inch)
Preheat adapters and edge to 150° C (302° F) minimum temperature with a maximum interpass temperature of 260° C (500° F). Assemble adapter bevel with hard contact against the base edge bevel while equalizing the gaps of the adapter straps. The minimum gap requirement for equalization is 3 mm (0.12 inch) and must be equalized within 3 mm ( 0.12 inch) to base edge surfaces. Use soft wire spacers to hold position while tack welding at mid length in root of J-Groove on each side of the top strap.
Begin first weld bead at the front of top strap weld groove root at point (B) or (G) as shown in Illustration 1. Apply weld passes in sequence to the groove to point (C) or (H).
Move to the other side of the adapter and repeat Step 2. Fill both J-grooves with alternating weld passes.
Turn edge over (Bottom side up) and repeat the procedures in Steps 2 and 3 for the bottom straps.
Continue welding alternate sides of the bottom strap until grooves are filled.
Start the first fillet weld pass at point (A) or (F). Start succeeding weld beads slightly behind the preceding layer to produce a rounded weld start as shown in Illustration 2. Continue welds 25 - 50 mm (1.0 - 2.0 inch) past the rear of the adapter shown by point (D) or (I), while tapering the weld to 3 mm (0.12 inch) at the end. Fillet weld bead passes should also be applied alternately on each side of the strap from front to back as described in Step 2. The final weld pass should be on the previously deposited weld near, but not on, the base edge weld toe.
Finish the tail welds. Begin the next weld at the rear of the adapter shown by point (E) or (J) in Illustration 1. Make the weld in one continuous pass 25 - 50 mm (1.0 - 2.0 inch) beyond the rear of the adapter shown by point (D) or (I) in Illustration 1, while tapering the weld to 3 mm (0.12 inch) at the end.Note: The same number of fillet weld passes should be applied to each side as per Step 6.
Move to the other side of the adapter and repeat Step 7.
Weld all bottom straps as per Steps 5 through 8.
Turn the edge back over (top side up), and complete the fillet welding of the top straps as per Step 6 through 8.
If necessary, use grinding to blend all start, stops, and weld toe undercuts. All weld stops (after initial pass) must tie into previously applied weld ends.
Allow finished welds to slow cool.

Caterpillar parts catalog:

Caterpillar parts catalog
8-16B EXTEND-A-MAT Screed 3GL00001-UP
10-20B, 10-20WB EXTEND-A-MAT Screed 3HL00001-UP
10-20B 10-20WB EXTEND-A-MAT Screed 3EL00001-UP
8-16B EXTEND-A-MAT Screed 2JN00001-UP
10-20B EXTEND-A-MAT Screed 2KN00001-UP
8B Pavemaster Screed 3LM00001-UP
10B Pavemaster Screed 3PM00001-UP
CATERPILLAR AP-1050B BARBER-GREENE BG-245C Asphalt Pavers 4XN00001-UP (MACHINE) POWERED BY 3116 Engine
Caterpillar AP-1055B, Barber-Greene BG-2455C Asphalt Pavers 6TN00001-UP (MACHINE) POWERED BY 3116 Engine
10B PAVEMASTER Screed 3RM00001-UP
10-20B EXTEND-A-MAT Screed 2LN00001-UP
8B PAVEMASTER Screed 3JM00103-UP
10B PAVEMASTER Screed 3NM00001-UP
10B PAVEMASTER Screed 3MM00001-UP
8-16B Screed 7MR00001-UP
8B PAVEMASTER Screed 7NR00001-UP
10B PAVEMASTER Screed BKB00001-UP
AP-655C.BG-2255C Asphalt Paver CDG00001-UP (MACHINE) POWERED BY 3056 Engine
8-16B SCREED BWL00001-UP


Parts plate Caterpillar catalog:

1077694 PLATE-THRUST
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 135H, 135H NA, 140G, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 2290, 2390, 2...
7C5802 PLATE-CLAMP
120H, 120H NA, 135H, 135H NA, 214B, 3114, 3116, 3126, 3176, 3176B, 320 L, 320B, 322 FM L, 322 LN, 325, 325 L, 325 LN, 325B, 325B L, 446, 446B, 446D, 45, 561M, 613C II, 918F, 924F, 928G, 938F, 950F, 95...
6H5139 PLATE-PRESSURE
120G, 12F, 12G, 130G, 140, 141, 14E, 14G, 153, 16, 163, 16G, 172, 173B, 183, 183B, 184, 191, 193, 30/30, 416, 416B, 426B, 428, 428B, 438B, 446, 46, 508, 515, 517, 518, 525, 525D, 527, 528, 535D, 545D,...
9T2232 PLATE-WAFER
30/30, 428, 5130, 65C, 75C, 75D, 85C, 85D, 918F, 924F, 928F, 928G, 928H, 928HZ, AP-1000, AP-1000B, AP-1055B, AP-650B, AP-800C, AP-800D, AP-900B, BG-225B, BG-225C, BG-2455C, BG-245C, D4H, D4H XL, D4HTS...
9T3030 PLATE
416, 426, 436, 517, 527, 65C, 75C, 75D, 85C, 85D, AP-1000B, AP-1055B, AP-650B, BG-225C, BG-2455C, BG-245C, D5H, D5H XL, D5HTSK II, D6M
6E6585 PLATE-LIMITER
426, 517, 527, 65C, 65E, 75C, 75D, 75E, 85C, 85D, 85E, 95E, AP-1000B, AP-1055B, AP-650B, BG-225C, BG-2455C, BG-245C, D5H, D5H XL, D5HTSK II, D6M
9T3860 PLATE
30/30, 428, 5130, 65C, 75C, 75D, 85C, 85D, 918F, 924F, 928G, 928H, 928HZ, 938F, 938G, 938G II, 988F, 988F II, AP-1000, AP-1000B, AP-1055B, AP-650B, AP-800C, AP-800D, AP-900B, BG-225B, BG-225C, BG-2455...
9X4821 PLATE AS
120H, 120H ES, 120H NA, 120K, 120K 2, 12K, 135H, 135H NA, 140G, 140K, 140K 2, 160K, 214B, 224B, 3116, 3126, 3126B, 3126E, 320 L, 320B, 322, 322B L, 322B LN, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 3...
7X5513 PLATE
AP-1000, AP-1000B, AP-1050, AP-1055B, AP-1200, AP-800, AP-800C, AP-900B, BG-225B, BG-225C, BG-2455C, BG-245C, CP-433B, CP-433C, CP-433E, CP-44, CP-563, CS-323C, CS-423E, CS-431B, CS-431C, CS-433C, CS-...
1247350 PLATE
10 FT, 10-20B, 10B, 8 FT, 8-16B, AP-655C, BG-2455C, BG-245C
1340041 PLATE-SPLICE
10 FT, 10-20B, 10B, 8 FT, 8-16B, AP-655C, BG-2455C, BG-245C
8I0987 PLATE AS
8 FT, 8-16B, AP-655C
8I0301 PLATE AS
8 FT, 8-16B, AP-655C
8I0298 PLATE AS
8 FT, 8-16B, AP-655C, AS3251C
8I0299 PLATE AS
8 FT, 8-16B, AP-655C, AS3251C
1653560 PLATE
10 FT, 10-20B, 8 FT, 8-16B, AP-1055D, AS3251C, AS3301C, BG-2455D, BG-260D
1653559 PLATE
10 FT, 10-20B, 8 FT, 8-16B, AP-1055D, AS3251C, AS3301C, BG-2455D, BG-260D
1653558 PLATE
10 FT, 10-20B, 8 FT, 8-16B, AP-1055D, AS3251C, AS3301C, BG-2455D, BG-260D
1466857 PLATE AS-COVER
10 FT, 10-20B, 8 FT, 8-16B, AP-655C
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.