AVSPARE.COM
parts catalog

PLATE & FILM GP 2278139 - Caterpillar



2278139 PLATE & FILM GP Caterpillar parts TH210 PLATE
Rating:
50
Alternative (cross code) number:
CA2278139
227-8139
2278139
Caterpillar 2278139 PLATE & FILM GP

Buy PLATE & FILM GP 2278139 Caterpillar genuine, new aftermarket tractor parts with delivery
TELEHANDLER,

Compatible equipment models: 2278139:

TELEHANDLER  TH210   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:

The CID 1197 diagnostic code is associated with the blade lower solenoid. The FMI13 diagnostic code is recorded when the Implement ECM determines that the blade lower solenoid requires calibration. This diagnostic code will only appear when the solenoid has been replaced or new software has been flashed into the ECM.System Response:A level 1 warning is generated. The blade lower may be slow to respond. The solenoid is out of calibration.Test Step 1. PERFORM CALIBRATION
Perform the calibration procedure for the ripper control handle. Refer to Testing and Adjusting, "Calibration" procedure in the service manual for your machine.
Observe the status of the CID 1197 FMI 13 diagnostic code. Expected Result:The CID 1197 FMI 13 diagnostic code is not active.Results:
OK - The CID 1197 FMI 13 diagnostic code is not active. The calibration corrected the condition that caused the diagnostic code. The calibration procedure was performed successfully.Repair: Resume normal machine operation.STOP
NOT OK - The CID 1197 FMI 13 diagnostic code is active. The calibration procedure was not performed successfully.Repair: Verify that the correct Implement ECM is installed on the machine. Verify that the correct software has been flashed into the ECM. Then repeat the calibration.If the diagnostic code is still active and the cause is not found, the ECM may have generated this diagnostic code in error.Exit this procedure and perform this procedure again. If the cause of the diagnostic code is not found, you may need to replace the ECM. Prior to replacing an ECM, contact the Technical Communicator at your dealership for a possible consultation with Caterpillar. This consultation may greatly reduce repair time. If the ECM requires replacing, refer to Testing and Adjusting, "Electronic Control Module (ECM) - Replace".STOP

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
TH210 Telehandler CEC00001-UP (MACHINE) POWERED BY 3054 Engine


Parts plate Caterpillar catalog:

1377351 PLATE-WARNING
TH103, TH210, TH215, TH62, TH63, TH82, TH83
1922637 PLATE
216, 216B, 216B3, 226B, 226B3, 228, 232B, 236, 236B, 236B3, 242B, 242B3, 246C, 247, 247B, 247B3, 248, 252B, 252B3, 256C, 257B, 257B3, 259B3, 262C, 262C2, 267, 267B, 268B, 272C, 277C, 277C2, 279C, 279C...
1151162 PLATE
3054C, 3054E, 315C, 416D, 424D, AP-300, C4.4, CB-434B, CB-434C, CB-534D, CB-544, CB-545, CB-564D, CP-433C, CS-323C, CS-431C, M313C, M315C, TH210, TH215, TH460B
2043093 PLATE
424B, 424B HD, CP-433E, CP-44, CS-423E, CS-433E, CS-44, TH210, TH215
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.