AVSPARE.COM
parts catalog

PLATE 2278166 - Caterpillar



2278166 PLATE Caterpillar parts SW345B, SW60 PLATE
Rating:
55
Alternative (cross code) number:
CA2278166
227-8166
2278166
Caterpillar 2278166 PLATE

Buy PLATE 2278166 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL SAW,

Compatible equipment models: 2278166:

WHEEL SAW  SW345B   SW60   Caterpillar
Number on catalog scheme: 12
 
  For full view, you need register

Information:

1. Refer to the illustration in order to install the polyurethane buffer seal (1) in the inner groove of the cylinder head.2. Install the backup ring (2) for the buffer seal in the inner groove on top of plyurethane buffer seal (1). The backup ring for the buffer seal should face toward the rod end.3. Install the U-Cup seal (3) in the head. Install the seal with the open end of the "U" facing toward the piston end of the cylinder.4. Use sandpaper or emery cloth in order to scuff the surfaces of the counterbore in the cylinder head and the outside diameter of the wiper seal's metal shell (4).5. Clean the counterbore in the head and the outside diameter of the wiper seal's metal shell with 8T-9011 Compound Cleaner or 6V- Quick Cure Primer. Clean the counterbore and the metal shell until neither of the components discolor a clean white towel. The metal shell of the wiper seal is coated with a corrosion inhibitor. This may prevent proper bonding of the wiper seal to the cylinder head if the inhibitor is not removed. After cleaning, do not touch the counter bore or the metal shell because the oil from your fingers may prevent a good bond. Handle the seal by the lip only6. Apply 6V-1541 Quick Cure Primer on the counterbore and the metal shell. Allow the primer to dry. The primer will dry in approximately 30 seconds.7. Apply 7M-7456 Bearing Mount Compound evenly but do not apply the compound excessively. Apply the compound to the counter bore and the metal shell. Do NOT allow the compound to contact the sealing lip. 8. Press the wiper seal (4) into the cylinder head. Refer to item (B) in order to make sure that the marking "THIS SIDE OUT" on the seal is toward the rod end. This seal should be firmly seated against the bottom of the counterbore. Wipe away any excess Bearing Marking Coumpound. Allow the compound to dry for 15 minutes before assembling the hydraulic cylinder. 9. Lightly lubricate the seals with clean hycraulic fluid before installing the head of the cylinder rod.COPYRIGHT 2001 CATERPILLAR ALL RIGHTS RESERVED

Caterpillar parts catalog:

Caterpillar parts catalog
SW45 & SW60 Wheel Saws WLS00001-UP (MACHINE)
SW345B, SW360B & SW460B Wheel Saws HFS00001-UP (MACHINE)


Parts plate Caterpillar catalog:

3V0046 PLATE
10 FT, 10-20B, 30/30, 307C, 307D, 308D, 311C, 311D LRR, 312C L, 312D, 312D L, 314C, 314D CR, 314D LCR, 315C, 315D L, 316E L, 318C, 319D, 319D L, 319D LN, 320C, 320D, 320D L, 320D LRR, 320D RR, 320D2 L...
2247370 PLATE-GUIDE
PC206, PC310B, SW345B, SW60
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.