AVSPARE.COM
parts catalog

PLATE AS 3157299 - Caterpillar



3157299 PLATE AS Caterpillar parts PLATE
Rating:
31
Alternative (cross code) number:
CA3157299
315-7299
3157299
Caterpillar 3157299 PLATE AS

Buy PLATE AS 3157299 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 1 g02724087
Connections of the Rear Axle Oil Temperature Sensor
This diagnostic code is associated with the Rear Axle Oil Temperature Sensor. This diagnostic code is recorded when the ECM reads the signal from the sensor (wire 446-PU(Purple)) as being shorted to the +battery. The signal (wire 446-PU(Purple)) connects to contact J2-27 of the ECM.Possible causes of the diagnostic code are listed:
The return circuit is open.
The signal circuit is open or the sensor is disconnected.
The signal circuit is shorted to the +battery.
The sensor has failed.
The ECM has failed. The failure of the ECM is unlikely.Before performing this procedure, inspect the harness connectors that are involved in the circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all of the connections in the circuit are clean and secure. If a problem with a connection is found, correct the problem and verify that this diagnostic code is active before performing this procedure.The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear the diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 0428 FMI 03 is active before performing this procedure.Test Step 1. CHECK FOR AN OPEN IN THE RETURN CIRCUIT.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the sensor from the machine harness.
At the machine harness connector for the sensor, measure the resistance from contact 2 (wire J842-BK(Black)) to ground. Expected Result:The resistance measurement should measure less than 5 ohms.Results:
OK - The resistance measurement is less than 5 ohms. The return circuit is correct. Proceed to Test Step 2.
NOT OK - The resistance that is measured is not correct.Repair: There is an open in the machine harness. The open is in the return circuit. Repair the harness or replace the harness.STOPTest Step 2. CHECK FOR AN OPEN IN THE SIGNAL CIRCUIT.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the J1 and J2 machine harness connector from the ECM.
At the machine harness connector for the sensor, install a jumper wire from contact 3 (wire 446-PU(Purple)) to contact 2 (wire J842-BK(Black)).
At the machine harness connector J1, measure the resistance from contact J2-27 (wire 446-PU(Purple)) to J1-45 (wire J842-BK(Black)). Expected Result:The resistance should measure less than 5 ohms.Results:
OK - The resistance measures less than 5 ohms. Proceed to 3.
NOT OK - The resistance measurement is greater than 5 ohms.Repair: There is an open in the signal circuit. Repair the harness or replace the harness.STOPTest Step 3. CHECK THE SIGNAL CIRCUIT FOR A SHORT.
The disconnect switch and the key start switch remain in the OFF position.
The machine harness connectors J1 and J2 remain disconnected.
Remove the jumper wire from contact 3 (wire 446-PU(Purple)) to contact 2 (wire J842-BK(Black)).
At the J1 and J2 machine harness connectors for the ECM, measure the resistance for the signal contact of the sensor J2-27 (wire 446-PU(Purple)) to all other J1 and J2 contacts. Expected Result:Each resistance measurement should be greater


Parts plate Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.