AVSPARE.COM
parts catalog

PLATE AS 3598656 - Caterpillar



3598656 PLATE AS Caterpillar parts 320E, 320E RR PLATE
Rating:
29
Alternative (cross code) number:
CA3598656
359-8656
3598656
Caterpillar 3598656 PLATE AS
Weight: 4 pounds 2 kg.

Buy PLATE AS 3598656 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Compatible equipment models: 3598656:

EXCAVATOR  320E   320E RR   Caterpillar
Number on catalog scheme: 6
 
  For full view, you need register

Information:


Release all the pressure in the hydraulic system prior to disconnecting any hydraulic lines or removing any loader linkage pins. If the hydraulic oil pressure is not released completely, oil can spray out of the oil lines under very high pressure. Also, there will be binding of the pins in their bores. After removal of any of the pins the loader linkage can separate suddenly. Failure to release system pressure completely can cause personal injury.
2. Lower the lift arms to the ground and be sure all hydraulic pressure is released. 3. Fasten a nylon strap and a hoist to the tilt cylinder, or put wood blocks between the tilt cylinders and the lift arms to prevent movement of the tilt cylinders during the removal of the linkage plates. 4. Put wood blocks between the coupler assembly and the lift arms to prevent the coupler from moving after the linkage plates are removed.5. Remove bolts, nuts and washers (1), and remove plates (3) from the machine.6. Note the position of washers (4) and (2) so they can be reinstalled to their original position.7. If necessary, remove the washers and the pins from the lever assembly and the lift arms. The following steps are for the installation of the linkage plates.8. Be sure all pins slide freely in their bores before assembly. Lubricate all pins, pin bores and seals with 5P0960 Multipurpose Grease before assembly.9. Install the tilt linkage plates in the reverse order for removal.10. Install pins (2) with the grease hole pointed toward the rear of the vehicle. Be sure washers (4) are installed in their original position.11. If any loader linkage parts were replaced with new ones, see Implement Control Group in Specifications for the correct amount of washers (4) to use in order to keep the lift arms centered in the coupler assembly.12. Be sure pins (2) protrude evenly from each plate and then tighten nuts (1) to a torque of 300 30 N m (220 22 lb ft).

Caterpillar parts catalog:

Caterpillar parts catalog
325F L Excavators NDJ00001-UP (MACHINE) POWERED BY C4.4 Engine
320E & 320E L Excavators AWS00001-UP (MACHINE) POWERED BY C6.6 Engine
320E RR & 320E LRR Excavators LHN00001-UP (MACHINE) POWERED BY C6.6 Engine
325F L Excavators XAA00001-UP (MACHINE) POWERED BY C4.4 Engine


Parts plate Caterpillar catalog:

8P9770 PLATE
14G, 215, 215B, 215C, 215D, 225, 225D, 229, 229D, 231D, 235, 235B, 235C, 235D, 245, 245B, 24H, 24M, 307C, 311C, 311D LRR, 311F LRR, 312, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 3...
0858828 PLATE
311, 311B, 311C, 311D LRR, 311F LRR, 312, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2, 313D2 LGP, 314C, 314D LCR, 314E CR, 314E LCR, 315, 316E L, 320D...
1348948 PLATE
115, 312, 315, 315C, 317, 318B, 318C, 319C, 319D, 319D LN, 320 L, 320B, 320C, 320C L, 320D, 320D GC, 320D L, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321C...
4I3308 PLATE
315, 315B, 315B L, 315C, 315D L, 316E L, 317, 317B LN, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320B FM LL, 320B U, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM ...
1076954 PLATE-FRICTION
311C, 313D2 LGP, 315C, 315D L, 316E L, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320B, 320B FM LL, 320B L, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 32...
1686761 PLATE AS
311C, 313D2 LGP, 315C, 315D L, 316E L, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320C, 320C L, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 3...
7Y1746 PLATE
311C, 313D2 LGP, 315C, 315D L, 316E L, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320C, 320C L, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 3...
1453035 PLATE
315C, 315D L, 318C, 318E L, 319C, 319D, 319D L, 319D LN, 320C, 320C L, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 3...
1733444 PLATE
315D L, 316E L, 318C, 318D L, 318E L, 319C, 319D, 319D L, 319D LN, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L...
1733443 PLATE
315D L, 316E L, 318C, 318D L, 318E L, 319C, 319D, 319D L, 319D LN, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L...
1733445 PLATE-VALVE
315D L, 316E L, 318C, 318D L, 318E L, 319C, 319D, 319D L, 319D LN, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L...
1733451 PLATE-SEPARATOR
315D L, 316E L, 318C, 318D L, 318E L, 319C, 319D, 319D L, 319D LN, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L...
3598666 PLATE
320E, 320E RR
3598658 PLATE
320E, 320E RR
3090564 PLATE
320E, 320E RR
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.