AVSPARE.COM
parts catalog

PLATE 3599494 - Caterpillar



3599494 PLATE Caterpillar parts 320D, 320D FM, 320D FM RR, 324D FM, 324D FM LL, 325D FM, 330D FM PLATE
Rating:
77
Alternative (cross code) number:
CA3599494
359-9494
3599494
Caterpillar 3599494 PLATE
Weight: 0.79 pounds 0 kg.

Buy PLATE 3599494 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Compatible equipment models: 3599494:

EXCAVATOR  320D   320D FM   320D FM RR   324D FM   324D FM LL   325D FM   330D FM   Caterpillar
Number on catalog scheme: 7
 
  For full view, you need register

Information:

Selecting the Correct Cylinder Head Gasket
Illustration 3 g02902277
(a) 2 Notches
(b) 1 Notch
(c) Without Notch
Make sure to note the notch (a), (b), or (c) of cylinder head gasket in advance.
Replace the same notch (a), (b), or (c) as the original cylinder head gasket.
When replacing the piston, piston pin bushing, connecting rod or crank pin bearing, select the cylinder head gasket thickness to meet with the top clearance.
Illustration 4 g02902343
Measure the piston head protrusion or recessing from the crankcase cylinder face 4 spots per each piston using the dial gauge as shown in figure, and get the average of the measurements.
Use the table below to select an applicable cylinder head gasket.
Table 2
Head Gasket Notch Head Gasket Thickness Piston head protrusion or recessing from crankcase cylinder face
Before Tighten After Tighten
(a)-two notches 0.900 mm (0.0354 inch) 0.800 mm (0.0315 inch) 0.0775 to 0.150 mm (0.00305 to 0.00591 inch)
(b)-one notch 1.00 mm (0.039 inch) 0.900 mm (0.0354 inch) 0.150 to 0.250 mm (0.0059 to 0.0098 inch)
(c)-without notch 1.10 mm (0.043 inch) 1.00 mm (0.039 inch) 0.250 to 0.343 mm (0.0098 to 0.0135 inch) Top Clearance
Remove the cylinder head.
Illustration 5 g02908085
(3) Plastigauge
With the piston at TDC, use grease to affix three or four Plastigauge of a diameter 1.5 mm (0.059 inch) by 5.0 to 7.0 mm (0.20 to 0.27 inch) long to the crown of the piston; keep the gauges away from the intake valve and combustion chamber fittings.
Take the piston to an intermediate position, install the cylinder head, and tighten the head bolts to the specified torque.
Turn the crankshaft so the piston goes through TDC.
Illustration 6 g02908096
(4) Crushed Plastigauge
(5) Scale
Remove the cylinder head and compare the width of the crushed Plastigauge with the scale.
Table 3
Top clearance Factory Specification 0.60 to 0.80 mm 0.024 to 0.031 inch
If they are out of spec, check the oil clearance of the crank pin, journal, and piston pins.Cylinder Head Surface Flatness
Clean the cylinder head surface.
Illustration 7 g02908237
Illustration 8 g02908396
Place a straightedge on the cylinder head's four sides “A”, “B”, “C” and “D” and two diagonal “E” and “F”as shown in the figure. Measure the clearance with a feeler gauge.
Table 4
Cylinder head surface flatness Allowable limit 0.05 mm 0.002 inch Glow Plug
Illustration 9 g03362373
(1) Glow plug
(A) View of good glow plug
(B) View of bad glow plug
Table 5
Glow Plug 7.7 N m (68.15078 lb in) to 9.3 N m (82.31198 lb in)

Caterpillar parts catalog:

Caterpillar parts catalog
CUSTOM SUPPORT LITERATURE FOR THE 324D FM LGP JGK00001-UP (MACHINE)
324D FM JKR00001-UP (MACHINE) POWERED BY C7 Engine
324D FM Forest Swing Machine JLS00001-UP (MACHINE) POWERED BY C7 Engine
325D Forest Swing Machine General Forestry Application High Wide Undercarriage C7K00001-UP (MACHINE) POWERED BY C7 Engine
325D Forest Swing Machine Butt-N-Top Log Loader High Wide Undercarriage C8L00001-UP (MACHINE) POWERED BY C7 Engine
330D Forest Swing Machine L2K00001-UP (MACHINE) POWERED BY C9 Engine
320D FM Forest Swing Machine CYZ00001-UP (MACHINE) POWERED BY C6.4 Engine
320D RR FM Forest Swing Machine SRT00001-UP (MACHINE) POWERED BY 3066 Engine
320D Forest Machines BZF00001-UP (MACHINE) POWERED BY C6.4 Engine
320D Log Loader GKS00001-UP (MACHINE) POWERED BY C6.4 Engine
320D FM Forest Swing Machine BWW00001-UP (MACHINE) POWERED BY C6.4 Engine


Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.