AVSPARE.COM
parts catalog

PLATE AS 3967202 - Caterpillar



3967202 PLATE AS Caterpillar parts PLATE
Rating:
51
Alternative (cross code) number:
CA3967202
396-7202
3967202
Caterpillar 3967202 PLATE AS
Weight: 0.29 pounds 0 kg.

Buy PLATE AS 3967202 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 13
 
  For full view, you need register

Information:


To prevent possible injury, do not use the starter to turn the flywheel. Hot engine components can cause burns. Allow additional time for the engine to cool before measuring valve clearance.
If the valve lash requires adjustment several times in a short period of time, excessive wear exists in a different part of the engine. Repair the problem in order to prevent more damage to the engine.Not enough valve lash can be the cause of rapid wear of the camshaft and valve lifters. Not enough valve lash can indicate that the seats for the valves are damaged.Valves become damaged due to the following causes:
The fuel injection nozzles do not operate correctly.
Excessive dirt and oil are present on the filters for the air inlet.
Incorrect fuel settings on the fuel injection pump.
The load capacity of the engine is frequently exceeded.Too much valve lash can cause broken valve stems, springs, and spring retainers. Too much valve lash can be an indication of the following problems:
Worn camshaft and valve lifters
Worn rocker arms
Bent pushrods
Broken socket on the upper end of a pushrod
Loose adjustment screw for the valve lashIf the camshaft and valve lifters show rapid wear, look for fuel in the lubrication oil or dirty lubrication oil as a possible cause.The valve lash is measured between the top of the valve stem and the rocker arm lever.Valve Lash Check
The valve lash setting is for a cold engine.Valve Lash Setting Inlet valve ... 0.35 mm (0.014 inch) Exhaust valve ... 0.35 mm (0.014 inch)If the measurement is not within the acceptable clearance, adjustment is necessary. Refer to "Valve Lash Adjustment".Valve Lash Adjustment
Note: The No. 1 cylinder is at the front of the engine.
Illustration 1 g00323903
Setting the valve lash (1) Adjustment screw (2) Feeler gauge
Accidental engine starting can cause injury or death to personnel.To prevent accidental engine starting, turn the ignition switch to the OFF position, place a do not operate tag at the ignition switch location and disconnect and tape the electrical connection to the stop solenoid that is located on the fuel injection pump.
Remove the valve mechanism cover and perform the following procedure in order to adjust the valve lash:Note: Later engines may require the use of a TORX T27 driver to adjust valve lash.
Rotate the crankshaft in the normal rotation of the engine. When

Caterpillar parts catalog:

Caterpillar parts catalog
299D XHP Compact Track Loader NLC00001-UP (MACHINE)
272D XHP Skid Steer Loader SHY00001-UP (MACHINE) POWERED BY C3.8 Engine
272D XHP Skid Steer Loader ETL00001-UP (MACHINE) POWERED BY C3.8 Engine
299D XHP Compact Track Loader JST00001-UP (MACHINE) POWERED BY C3.8 Engine
297D/297D XHP Multi Terrain Loader BE700001-UP (MACHINE) POWERED BY C3.8 Engine


Parts plate Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.