AVSPARE.COM
parts catalog

PLATE AS-RH 3967568 - Caterpillar



3967568 PLATE AS-RH Caterpillar parts PLATE
Rating:
51
Alternative (cross code) number:
CA3967568
396-7568
3967568
Caterpillar 3967568 PLATE AS-RH

Buy PLATE AS-RH 3967568 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

Fuel Line Wrench For 3208 Engines
Because of its location, it is difficult to tighten the 5P7437 Nut (split nut) on the No. 1 fuel injection line at the fuel injection pump. The nut can easily be installed if the serviceman first fabricates a wrench.
To make the wrench, grind or saw a 5P331 Crowfoot Wrench to the dimensions shown in Illustration 1. Remove the roll pin and the crowfoot wrench from a 5P5195 Fuel Line Wrench, and install the 5P331 Crowfoot Wrench. Fasten the wrench to the handle with the roll pin.
Adjustment Of The 6V2197 Transducer
The 6V2197 Transducer must be installed approximately 0.5 mm to 2.0 mm (.02" to .08") from the face of the flywheel or gear to operate correctly.
If it is too close, it will not send an acceptable electrical signal to the indicator group. For example, a transducer installed too close to the camshaft drive gear on a 3208 Engine will read the rough surface of the gear instead of the timing hole. The timing indication can be constant and acceptable at low idle, but as the engine rpm is increased, it will rapidly change and will not be acceptable. The chart which follows shows typical indications from the 6V3100 Timing Indicator Group when the transducer is at different distances from the flywheel or gear.
It is difficult to correctly install the transducer by feel, but a 2D6392 O-Ring Seal makes it easier to find the correct distance. To do this, slide the seal on the transducer and install transducer in the transducer adapter until it makes contact with the flywheel or gear. Push the O-ring against the adapter face. Slowly pull the transducer back from the flywheel or gear; the distance between the O-ring and the adapter is the same as the distance between the transducer and the flywheel or the gear.
It is possible for one of the holes in a flywheel to be in alignment with the pin timing opening in the housing. Make sure the transducer is not in one of the holes. If necessary, remove the transducer, turn the flywheel with an engine rotation tool and install the transducer again.
Timing Indication Is Constant But Retarded At Constant Speed
It is possible for the indication to be constant but retarded (less than expected). If this condition is present, the electrical signal was probably read from a hole other than the timing hole in the flywheel. This condition is generally found when Caterpillar Engines are used with transmissions or torque converters from a different source in an Original Equipment Manufacturer's (OEM) product. The reason for this is special flywheels are used to connect the engines to the transmissions, and these flywheels generally have several holes in them. For example, when Caterpillar 3406 and 3408 Engines are used with Allison CT700, HT700, 5000 or 6000 Transmissions or TC500 Series Torque Converters, the indications can be approximately 7.6° off or 22.4° off. See the article, "Indications From 6V3100 Timing Indicator Group Must Be Corrected For Some Applications," in


Parts plate Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.