AVSPARE.COM
parts catalog

PLATE 3967601 - Caterpillar



3967601 PLATE Caterpillar parts PLATE
Rating:
26
Alternative (cross code) number:
CA3967601
396-7601
3967601
Caterpillar 3967601 PLATE

Buy PLATE 3967601 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 3
 
  For full view, you need register

Information:


Fuel leaked or spilled onto hot surfaces or electrical components can cause a fire. To help prevent possible injury, turn the start switch off when changing fuel filters or water separator elements. Clean up fuel spills immediately.
Do not allow dirt to enter the fuel system. Thoroughly clean the area around a fuel system component that will be disconnected. Fit a suitable cover over disconnected fuel system component.
Illustration 1 g00291145
Open the engine access covers and open the left side access door.
Illustration 2 g00294183
Turn the fuel supply valves to the OFF position before performing this maintenance. Place a tray under the fuel filter in order to catch any fuel that might spill. Clean up any spilled fuel immediately.
Illustration 3 g00294185
Illustration 4 g00304164
Clean the outside of the fuel filter assembly. Open drain (4) and drain the fuel and water from element (3) into a suitable container.Note: If the element is not equipped with a drain, remove cap (1). Remove the nylon insert in order to reduce the level of fuel in the element. A reduction in the level of fuel in the element will help prevent fuel from being spilled when the element is removed.
Do not use a tool in order to remove the fuel filter. Attempting to remove the fuel filter with a filter wrench or a filter strap could damage the locking ring.
Hold element (3) and rotate locking ring (2) counterclockwise. Remove locking ring (2). The used element should be removed and discarded.Note: If the element is equipped with a sediment bowl, remove the sediment bowl from the element. Thoroughly clean the sediment bowl. Inspect the O-ring seals. Install new O-ring seals, if necessary. Install the sediment bowl to the new element. Hand tighten the sediment bowl. Hand tightening is the only method that should be used.
Do not fill fuel filters with fuel before installing them. Contaminated fuel will cause accelerated wear to fuel system parts.
Ensure that the filter head is clean. Push a new element fully into the filter head.
Hold the element in place. Fit locking ring (2) into position. Rotate the locking ring clockwise in order to fasten the element to the filter head.Note: If the nylon insert was removed, install the nylon insert and install cap (1) .
Prime the fuel system. Refer to the Operation and Maintenance Manual in the Maintenance Section for more information.

Caterpillar parts catalog:

Caterpillar parts catalog
637K Wheel Tractor Scraper WTY00001-UP (MACHINE)
631K OEM Wheel-Tractor Sctraper WT400001-UP (MACHINE) POWERED BY C18 Engine
631K OEM Wheel-Tractor Scraper WT600001-UP (MACHINE) POWERED BY C18 Engine
631K Wheel Tractor Scraper WTR00001-UP (MACHINE) POWERED BY C18 ENGINE
637K Wheel Tractor Scraper WTS00001-UP (MACHINE)
637K Wheel Tractor Scraper WTT00001-UP (MACHINE)
631K Wheel Tractor Scraper WTW00001-UP (MACHINE) POWERED BY C18 Engine
637K Wheel Tractor Scraper WTX00001-UP (MACHINE)


Parts plate Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.