4415525 PLATE-WEAR(RH) Caterpillar parts
Rating:
Alternative (cross code) number:
CA4415525
441-5525
4415525
CA4415525
441-5525
4415525
For full view, you need register
Information:
EtherNet/IP Codes
The messages that are shown on the following table will appear on the terminal screen as "DC Error=xx". If an alert is displayed that is not listed in the table, contact technical support.
Table 2
Error Number Terminal Messages Type Meaning Recommended Action
xx,xx,xx Number depends on hardware fault detected. Communication Interface Fault Critical Fault A hardware problem was detected during power-up. If you ignore message and display the EtherNet/IP Communications Scree, the Comm Status displays "Comms hardware fault:" without an error number. The FW revision, serial number and EtherNet/IP address fields are displayed. Contact technical support to have unit repaired.
770 Buffer overflow Comm Status Internal error occurred. Contact technical support.
771 Buffer overflow Comm Status Internal error occurred. Contact technical support.
1799 Heap Partition empty Comm Status Internal error occurred. Contact technical support.
16387 Comms not started yet Comm Status The PanelView has not connected to the network. Check IP configuration (on the Communication Setup scree) and wait for PanelView to connect to the network.
16388 CIP S/N is not valid Critical fault. DC incorrectly configured. Contact technical support.
16389 Out of buffers Critical fault. No buffers are available for read or write operations. Contact technical support.
16390 An intial write failed Comm Warning Write to Logic Controller on Startup was configured and on powerup, the PanelView could not write initial values to a node's data table address. or Write to Logic Controller on Startup was not configured and the PanelView was unable to write a controller. Note: The error is only displayed on the first write attempt. Check/define data table address in the controller. Check communication connections and node configuation in the application.
16391 PV write failed Comm Warning PanelView is communicating with the controller. The data table address does not exist. Check/define data table address in the controller.
16392 PV write timeout Comm Warning PanelView is communicating with the logic controller. Check connections and node configuration in the application.
16393 PV read fail Comm Warning PanelView is communicating with the controller. The data table address does not exist. Check/define data table address in the controller.
16394 PV read timeout Comm Warning PanelView is not communicating with the controller. Check/define data table address in the controller.
16397 CN object received a reset request Comm Warning An Ethernet object reveived a reset request from a device on the network. The PanelView does not support network resets.
16398 The Connection Originator is indicating it is in Program Mode Comm Warning The logic controller is offline (in Program Mode). The COMM LED on the Configuration Mode
The messages that are shown on the following table will appear on the terminal screen as "DC Error=xx". If an alert is displayed that is not listed in the table, contact technical support.
Table 2
Error Number Terminal Messages Type Meaning Recommended Action
xx,xx,xx Number depends on hardware fault detected. Communication Interface Fault Critical Fault A hardware problem was detected during power-up. If you ignore message and display the EtherNet/IP Communications Scree, the Comm Status displays "Comms hardware fault:" without an error number. The FW revision, serial number and EtherNet/IP address fields are displayed. Contact technical support to have unit repaired.
770 Buffer overflow Comm Status Internal error occurred. Contact technical support.
771 Buffer overflow Comm Status Internal error occurred. Contact technical support.
1799 Heap Partition empty Comm Status Internal error occurred. Contact technical support.
16387 Comms not started yet Comm Status The PanelView has not connected to the network. Check IP configuration (on the Communication Setup scree) and wait for PanelView to connect to the network.
16388 CIP S/N is not valid Critical fault. DC incorrectly configured. Contact technical support.
16389 Out of buffers Critical fault. No buffers are available for read or write operations. Contact technical support.
16390 An intial write failed Comm Warning Write to Logic Controller on Startup was configured and on powerup, the PanelView could not write initial values to a node's data table address. or Write to Logic Controller on Startup was not configured and the PanelView was unable to write a controller. Note: The error is only displayed on the first write attempt. Check/define data table address in the controller. Check communication connections and node configuation in the application.
16391 PV write failed Comm Warning PanelView is communicating with the controller. The data table address does not exist. Check/define data table address in the controller.
16392 PV write timeout Comm Warning PanelView is communicating with the logic controller. Check connections and node configuration in the application.
16393 PV read fail Comm Warning PanelView is communicating with the controller. The data table address does not exist. Check/define data table address in the controller.
16394 PV read timeout Comm Warning PanelView is not communicating with the controller. Check/define data table address in the controller.
16397 CN object received a reset request Comm Warning An Ethernet object reveived a reset request from a device on the network. The PanelView does not support network resets.
16398 The Connection Originator is indicating it is in Program Mode Comm Warning The logic controller is offline (in Program Mode). The COMM LED on the Configuration Mode