AVSPARE.COM
parts catalog

PLATE AS 4645063 - Caterpillar



4645063 PLATE AS Caterpillar parts PLATE
Rating:
26
Alternative (cross code) number:
CA4645063
464-5063
4645063
Caterpillar 4645063 PLATE AS
Weight: 1 pounds 0 kg.

Buy PLATE AS 4645063 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 3
 
  For full view, you need register

Information:


Illustration 2 g00884350
Apply 5P-0960 Molybdenum Grease on pin assembly (18). Use a hoist and a lifting sling to position pin assembly (18). Temporarily install the spacer and pin assembly (18). The weight of the pin assembly is approximately 48 kg (105 lb). Note: Do not remove the hoist from the boom cylinder at this time.
Illustration 3 g00884369
(X) Boom Cylinder
(Y) Support Pin
(Z) Upper Frame
Slide the boom cylinder to one side until the boom cylinder contacts the frame. Measure the total clearance between the boom cylinder and the frame at the pin bore. The total clearance of (a) and (b) may not be more than 1.0 mm (0.04 inch). If the total clearance is less than 1.0 mm (0.04 inch), the addition of shims between the boom cylinder and frame will not be required. If the total clearance is more than 1.0 mm (0.04 inch), add the correct thickness of shims in order to obtain the necessary clearance.
After the boom cylinder has been properly shimmed, install the spacer and pin assembly (18). Install bolt (17). The weight of the pin assembly is approximately 48 kg (105 lb).
Illustration 4 g00591845
Lower boom cylinder (4) onto Tooling (B). Adjust the height of Tooling (B) so the boom cylinder is level.
Illustration 5 g00588922
Position support assemblies (16) and install bolts (15).
Illustration 6 g00574973
Position tube assembly (14) and install bolts (13).
Illustration 7 g00589120
Position tube assembly (12) and install bolts (11).
Illustration 8 g00574977
Position clamp (10) and install bolts (9).
Illustration 9 g00588978
Position hose assemblies (8) and install bolts (7).
Illustration 10 g00574972
Install bolts (6).
Illustration 11 g00591861
Use a lifting sling and a hoist to position boom cylinder (4). Raise the boom cylinder in order to align the rod end of the boom cylinder with the boom cylinder support pin.
Illustration 12 g00591894
Install Tooling (A) on the boom cylinder support pin on the opposite side of the boom cylinder that is being installed.
Use a hammer to drive the boom cylinder support pin into the rod end of the boom cylinder until the boom cylinder support pin is centered in the boom.
Illustration 13 g00591906
Position the spacer and retainer plate (3), and install bolts (2).
Remove Tooling (A). Repeat Step 15 in order to install the retainer plate on the opposite boom cylinder.
Illustration 14 g00574959
Connect lubrication hose assembly (1).
Fill the hydraulic oil tank with oil to the correct level. Refer to Operation and Maintenance Manual, "Lubricant Viscosities" for the proper oil viscosity and Operation and Maintenance Manual, "Hydraulic System Oil Level - Check".
Lubricate the boom mounting pin and the boom cylinder mounting pins. Refer to Operation and Maintenance Manual, "Boom, Stick and Bucket Linkage - Lubricate".
Start the engine, and run the engine at low idle speed. Move the joystick for the boom in order to extend and retract the boom cylinders. Cycle the boom cylinders approximately ten times in order to remove the air from the hydraulic system.
Recheck the oil level in the hydraulic oil tank. If necessary, refill the hydraulic oil tank to the correct level.

Caterpillar parts catalog:

Caterpillar parts catalog
972M Wheel Loader A8P00001-UP (MACHINE) POWERED BY C9.3 Engine
972M Wheel Loader JPR00001-UP (MACHINE) POWERED BY C9.3 Engine
966M Wheel Loader KJP00001-UP (MACHINE) POWERED BY C9.3 Engine
966M Wheel Loader DYC00001-UP (MACHINE) POWERED BY C9.3 Engine
966M XE Wheel Loader P6C00001-UP (MACHINE) POWERED BY C9.3 Engine
972M XE Wheel Loader EDW00001-UP (MACHINE) POWERED BY C9.3 Engine


Parts plate Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.