AVSPARE.COM
parts catalog

PLATE-WEAR 4646194 - Caterpillar



4646194 PLATE-WEAR Caterpillar parts PLATE
Rating:
51
Alternative (cross code) number:
CA4646194
464-6194
4646194
Caterpillar 4646194 PLATE-WEAR
Weight: 0.22 pounds 0 kg.

Buy PLATE-WEAR 4646194 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 1 g01325350
Schematic of the Auxiliary Valve #1 Port A Solenoid (Ripper/Plow Raise Solenoid) (12 pin ECM connection)
Illustration 2 g02717337
Schematic of the Auxiliary Valve #1 Port A Solenoid (Ripper/Plow Raise Solenoid) (70 pin ECM connection)This diagnostic code is associated with the Auxiliary Valve #1 Port A Solenoid (Ripper/Plow Raise Solenoid). The FMI 06 means that the ECM has determined that there is a short to ground in the solenoid circuit.The possible causes of this diagnostic code are listed:
The energize circuit of the solenoid is shorted to ground.
The solenoid has failed.
The ECM has failed. This is unlikely.Before performing this procedure, inspect the harness connectors that are involved in the circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all connections in the circuit are clean, secure and in good condition. If a problem with a connection is found, correct the problem and verify that this diagnostic code is active before performing this procedure.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 2212 FMI 06 is active before performing this procedure.Note: Use a Digital Multimeter for the measurements in this procedure.System Response:A level 1 warning will be generated. Test Step 1. CHECK THE SOLENOID.
Turn the disconnect switch and the key start switch to the ON position. DO NOT start the engine.
Disconnect the solenoid with the active diagnostic code from the machine harness.
Observe the status of the diagnostic code.Expected Result:CID 2212 FMI 06 changes to CID 2212 FMI 05 when the solenoid is disconnected. Results:
YES - CID 2212 FMI 06 changes to CID 2212 FMI 05 when the solenoid is disconnected. The circuit is correct. Repair: The solenoid has failed. Replace the solenoid. Verify that the new solenoid corrects the problem.STOP
NO - The CID 2212 FMI 06 remains active. Proceed to test step 2.Test Step 2. CHECK THE ENERGIZE CIRCUIT OF THE SOLENOID FOR A SHORT TO GROUND.
Turn the key start switch and the disconnect switch to the OFF position.
The solenoid remains disconnected from the machine harness.
Disconnect the machine harness connector(s) from the ECM.
At the machine harness connector, measure the resistance from the signal contact (wire J921-PK) to all contacts that are used in the machine harness connectors for the ECM.Expected Result:Each resistance measurement is greater than 5000 ohms.Results:
OK - Each resistance is greater than 5000 ohms. The machine harness is correct. Proceed to test step 3.
NOT OK - Each resistance measurement is not greater than 5000 ohms. There is a short in the machine harness. The short is between the signal contact (wire J921-PK) and the circuit with the low resistance measurement.Repair: Repair the machine harness or replace the machine harness.STOPTest Step 3. CHECK IF THE DIAGNOSTIC CODE REMAINS.
Inspect the harness connectors and clean the contacts of the harness connectors. Check the wires for damage to the insulation that is caused by excessive heat, corrosion, or chafing.
Perform a


Parts plate Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.