AVSPARE.COM
parts catalog

PLATE-WEAR 4646200 - Caterpillar



4646200 PLATE-WEAR Caterpillar parts PLATE
Rating:
66
Alternative (cross code) number:
CA4646200
464-6200
4646200
Caterpillar 4646200 PLATE-WEAR
Weight: 1 pounds 0 kg.

Buy PLATE-WEAR 4646200 Caterpillar genuine, new aftermarket tractor parts with delivery

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below
Replace 61A-W0078-A2-00 Water Pump Kit with Impeller Housing Compatible with YAMAHA Outboards V6 150 175 200 225 250 300 HP
$45.00

23 Jun 2021

US: Tepeng Powersport
Replace 61A-W0078-A2-00 Water Pump Kit with Impeller Housing Compatible with YAMAHA Outboards V6 150 175 200 225 250 300 HP
Wztepeng Compatible with:Yamaha V6 Outboards 150, 175, 200, 225, 250 & 300 Hp Engines. Such as yamaha 1994 C115 (6E5), 1992-1994 L150 (6R0), 1992-1994 150 (6R2), 1992-1995 P150 (6N9), 1992-1995 175 (6R3), 1994 P175 (62H). || Content:1*Water Pump Impeller, 1*Imperller Housing, 1*Pump Cup, 1*Wear Plate, 1*Key, 1*Water Pump Gasket, 2*Pin, 4*Bolt & Washer, 2*O-Ring || Replace Part Number:61A-W0078-A2-00, 61A-W0078-A3-00, 18-3396, 9-48618, 46-46200 , 6E5-44352-01-00 , 6AW-44311-01 , 61A-44322-00 , 6G5-44323-00 , 6E5-44315-A0-00 , 90280-04002-00 , 93210-37M67-00 , 93210-86M38-00 , 93606-12019 , 90119-08M14-00 || Feature:We adopt the highest grade materials to make our product. It bring durable and reliable feature under extreme conditions. || Warranty:For any reason, if you are not satisfied with your purchase, contact us directly. We offer a one-year warranty, 100% satisfaction guarantee.
4 Strokes Water Pump Kit with Impeller Housing Compatible with YAMAHA Outboards 150 175 200 225 250 300 HP Replaces 61A-W0078-A2-00 61A-W0078-A3-00 18-3396
$45.00

24 May 2022

US: Tepeng Powersport
4 Strokes Water Pump Kit with Impeller Housing Compatible with YAMAHA Outboards 150 175 200 225 250 300 HP Replaces 61A-W0078-A2-00 61A-W0078-A3-00 18-3396
Wztepeng Compatible with:Yamaha V6 Outboards 150, 175, 200, 225, 250 & 300 Hp Engines. Such as yamaha 1994 C115 (6E5), 1992-1994 L150 (6R0), 1992-1994 150 (6R2), 1992-1995 P150 (6N9), 1992-1995 175 (6R3), 1994 P175 (62H). || Content:1*Water Pump Impeller, 1*Imperller Housing, 1*Pump Cup, 1*Wear Plate, 1*Key, 1*Water Pump Gasket, 2*Pin, 4*Bolt & Washer, 2*O-Ring || Replace Part Number:61A-W0078-A2-00, 61A-W0078-A3-00, 18-3396, 9-48618, 46-46200 , 6E5-44352-01-00 , 6AW-44311-01 , 61A-44322-00 , 6G5-44323-00 , 6E5-44315-A0-00 , 90280-04002-00 , 93210-37M67-00 , 93210-86M38-00 , 93606-12019 , 90119-08M14-00 || Feature:We adopt the highest grade materials to make our product. It bring durable and reliable feature under extreme conditions. || Warranty:For any reason, if you are not satisfied with your purchase, contact us directly. We offer a one-year warranty, 100% satisfaction guarantee.
Water Pump Impeller Kit 61A-W0078-A1 A2 & A3 for Yamaha F150 F150 F200 F225
$45.99

07 Jul 2021

CN: enochrose
Water Pump Impeller Kit 61A-W0078-A1 A2 & A3 for Yamaha F150 F150 F200 F225
Hi-fun Part Number:replaces OEM # 61A-W0078-01-00, 61A-W0078-A1-00, 61A-W0078-A2-00, 61A-W0078-A3-00 || Fits Yamaha V6 Outboards 150 HP, 175 HP, 200 HP, 225 HP, 250 HP, 300 HP || Kit includes: 61A-44322-02-00 - CARTRIDGE INSERT (1) 6E5-44352-01-00 - IMPELLER (1) 6G5-44323-00-00 - OUTER PLATE CARTRIDGE (1) 6E5-44315-A0-00 - WATER PUMP GASKET (1) 93210-37M67-00 - O-RING (1) 93210-86M38-00 - O-RING (1) 93606-12019-00 - DOWEL PIN (2) 90119-08M14-00 - BOLT WITH WASHER (4) 90280-04M05-00 - WOODRUFF KEY (1) || Our aftermaket Yamaha Outboard Impeller Water Pump Kit ONLY || Replaces Sierra 18-3396, Mallory 9-48618 & EMP 46-46200
  For full view, you need register

Information:


Illustration 1 g01318019
Schematic of the Hystat Joystick Control BaseThis diagnostic code is associated with the Joystick Forward/Reverse Position Sensor The FMI 08 diagnostic means that the ECM has determined that the signal frequency or the signal pulse width is not within the expected range. The sensor is a PWM sensor that operates at a frequency of approximately 500 hertz. The sensor has an operating duty cycle of 5% to 95%. The possible causes of this diagnostic code are listed below:
The sensor has failed.
Intermittent connections or poor connections
Mechanical devices are loose.
The ECM has failed. This is unlikely.Before performing this procedure, inspect the harness connectors that are involved in the circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all connections in the circuit are clean, secure and in good condition. If a problem with a connection is found, correct the problem and verify that this diagnostic code is active before performing this procedure.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear the diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 1699 FMI 08 is active before performing this procedure.Note: Use a Digital Multimeter for the measurements in this procedure. System Response:A level 2 warning will be generated. Functionality is lost and the ECM cannot determine desired direction. The machine will not be able to be moved.Test Step 1. CHECK FOR POWER AT THE SENSOR.
Do not disconnect the harness connector from the sensor.
At the back of the harness connector for the sensor, insert a 7X-1710 Multimeter Probe along contact 1 (wire 709-OR) for the voltage supply.
At the back of the harness connector for the sensor, insert a 7X-1710 Multimeter Probe along contact 2 (wire J764-BR) for the ground.
Turn the key start switch and the disconnect switch to the ON position.
Measure the voltage from contact 1 (wire 709-OR) to contact 2 (wire J764-BR).Expected Result:The voltage is 10 0.5 DCV.Results:
OK - The voltage is 10 0.5 DCV. Proceed to Test Step 3.
NOT OK - The voltage is not 10 0.5 DCV. The circuit is open. Repair: Repair the machine harness or replace the machine harness.STOPTest Step 2. CHECK THE SIGNAL CIRCUIT OF THE SENSOR.
Turn the key start switch and the disconnect switch to the OFF position.
At the back of the harness connector for the sensor, remove the 7X-1710 Multimeter Probe from contact 1 and insert the probe along the signal wire contact 5 (wire F853-BR).
The other 7X-1710 Multimeter Probe remains at the ground wire contact 2 (wire J764-BR).
Turn the disconnect switch and the key start switch to the ON position.
Monitor the signal of the sensor with the multimeter.
Without disconnecting the sensor or the hardware that is associated with the sensor from the machine, take the sensor through the full operating range of the sensor.Expected Result:The sensor's signal responds in the manner that is described at the beginning of this procedure.Results:
OK - The sensor's signal


Parts plate Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.