AVSPARE.COM
parts catalog

PLATE-WEAR 4646266 - Caterpillar



4646266 PLATE-WEAR Caterpillar parts PLATE
Rating:
46
Alternative (cross code) number:
CA4646266
464-6266
4646266
Caterpillar 4646266 PLATE-WEAR

Buy PLATE-WEAR 4646266 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 7
 
  For full view, you need register

Information:

Installation Procedure
Illustration 1 g00884398
Move the machine in position between the push arms and the blade assembly.
Move the machine ahead until push arms (7) engage with trunnion (10).
Illustration 2 g00884397
Install bolts (9) and cap (8) without the shims.
Tighten bolts (9) evenly.
Insert an equal amount of shims between the cap and the push arm assembly, as needed.
Add one additional shim to each of the spaces. The specified clearance between the trunnion and the push arm assembly is 0.50 0.25 mm (0.02 0.001 inch).
Tighten bolts (9) to a torque of 1800 200 N m (1327 148 lb ft).
Repeat Steps 3 through 7 for the opposite machine side.
Release the pressure in the hydraulic system. Refer to Disassembly and Assembly, "System Pressure - Release".
Illustration 3 g00884396
Connect hose assemblies (6).
Illustration 4 g00884393
Illustration 5 g00884395
Attach a suitable lifting device to stabilizer link (3). The weight of stabilizer link (3) is approximately 120 kg (265 lb).
Raise the end of stabilizer link (3) to the front trunnion.
Start the machine.
Carefully turn the machine to the right until stabilizer link (3) is engaged with the front trunnion.
Stop the machine.
Install bolts (5) and cap (4) without shims.
Tighten bolts (5) evenly on both sides of the cap.
Insert an equal amount of shims between the cap and the stabilizer link, as needed.
Add one additional shim to each of the spaces. The specified clearance between the trunnion and the stabilizer link is 0.50 0.25 mm (0.020 0.010 inch).
Tighten bolts (5) to a torque of 620 80 N m (460 60 lb ft).
Illustration 6 g00884392
Start the machine.
Extend the lift cylinder rods to the trunnions.
Stop the machine.
Install bolts (1) and cap (2) without the shims.
Tighten bolts (1) evenly on both sides of the cap.
Insert an equal amount of shims in the spaces between the bearing cap and the lift cylinder, as needed.
Add one additional shim to each of the spaces. The specified clearance between the trunnion and the rod assembly is 0.50 0.25 mm (0.020 0.010 inch).
Tighten bolts (1) to a torque of 620 80 N m (460 60 lb ft).
Repeat Steps 16 through 23 for the remaining lift cylinder.

Caterpillar parts catalog:

Caterpillar parts catalog
980M Wheel Loader MK200001-UP (MACHINE) POWERED BY C13 Engine
980M Wheel Loader MGD00001-UP (MACHINE) POWERED BY C13 Engine
980K Wheel Loader GTZ00001-UP (MACHINE) POWERED BY C13 Engine
980M Wheel Loader N8T00001-UP (MACHINE) POWERED BY C13 Engine


Parts plate Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.