AVSPARE.COM
parts catalog

PLATE 5088768 - Caterpillar



5088768 PLATE Caterpillar parts PLATE
Rating:
71
Alternative (cross code) number:
CA5088768
508-8768
5088768
Caterpillar 5088768 PLATE

Buy PLATE 5088768 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 7
 
  For full view, you need register

Information:


Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Do not let the tops of fuel injectors turn when the fuel line nuts are loosened or tightened.The fuel injectors will be damaged if the top of the injector turns in the body.The engine will be damaged if a defective fuel injector is used because the shape of fuel (spray pattern) that comes out of the nozzle will not be correct.
Note: Place identification marks on all tube assemblies for installation. Plug all lines and tube assemblies in order to prevent contamination.
Turn the fuel supply to the OFF position.
Illustration 1 g03341354
Use Tooling (A) to disconnect nuts (1) for fuel injection lines (3) from fuel injectors (2).
Use Tooling (A) to disconnect nuts (4) for fuel injection lines (3) from fuel injection pump (5).
Remove fuel injection lines (3) from the engine as an assembly.
Use suitable caps in order to plug the open ports of fuel injection pump (5) immediately.
Use suitable caps in order to plug the open ports of fuel injectors (2) immediately.
Illustration 2 g03341356
If fuel injectors (2) have been previously capped, the caps will need removing from fuel injectors (2) before removing nuts (7).
Use a deep socket in order to remove nuts (7) from fuel injectors (2). Note: For engines with a fuel return line, ensure that the fuel return line is not distorted when the nuts are loosened.
Remove banjo bolt (9) from fuel return line (6).
Remove sealing washers (10).
Remove fuel return line (6) from fuel injectors (2).
Remove sealing washers (8) from fuel injectors (2).
Use suitable caps in order to plug fuel injectors (2) immediately. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 276-1216 Injector Pipe Nut Tool 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Do not let the tops of fuel injectors turn when the fuel line nuts are loosened or tightened.The fuel injectors will be damaged if the top of the injector turns in the body.The engine will be damaged if a defective fuel injector is used because the shape of fuel (spray pattern) that comes out of the nozzle will not be correct.
Note: The installation procedure is similar for the three cylinder and the four cylinder engines.
Illustration 3 g03341356
Remove the caps from fuel injectors (2).
Install new sealing washers (8) to fuel injectors (2). Note: The sealing washers have two small holes.
Install fuel return line (3) onto fuel injectors (2).
Use a deep socket in order to install nuts (7) loosely to fuel injectors (2).
Install a new sealing washer (10) onto banjo bolt (9).
install banjo bolt (9) to rigid fuel return line (6).
Install remaining new sealing washer (10) between rigid fuel return line (6) and the connection on the fuel injection

Caterpillar parts catalog:

Caterpillar parts catalog
TH255C Telehandler JK201000-UP (MACHINE) POWERED BY 2.9 Engine


Parts plate Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.