parts catalog

PLATE, DRIVE 63000500 - Caterpillar

63000500 PLATE, DRIVE Caterpillar parts CB-614
Alternative (cross code) number:
Caterpillar 63000500 PLATE, DRIVE

Buy PLATE, DRIVE 63000500 Caterpillar genuine, new aftermarket tractor parts with delivery

Compatible equipment models: 63000500:

Number on catalog scheme: 8
  For full view, you need register


Illustration 1 g00891351
Schematic of the Switch ("Shear/Hammer" Selector)This switch has two inputs to the ECM. The two inputs are "SHEAR" and "HAMMER". During normal operation, one of the inputs is open. The other input is grounded. When a circuit is measured with a voltmeter, an open circuit will measure approximately 5 DCV and a closed circuit will measure approximately 0 DCV. An FMI 06 diagnostic code is recorded when the status of both the inputs are grounded.The possible causes of this diagnostic code are listed below:
The "SHEAR" signal circuit (wire H480-GN) is shorted to ground.
The "HAMMER" signal circuit (wire H481-PK) is shorted to ground.
The switch has failed.
The ECM has failed. This is unlikely. Test Step 1. CHECK THE SWITCH
Turn the key start switch to the ON position.
The diagnostic code is active.
Remove the wire from contact "2" (wire G939-PK) at the switch.
Toggle the switch and note the status of the diagnostic code.Expected Result:The diagnostic code is no longer active in either position.Results:
OK - The diagnostic code is no longer active in either position.Repair: The switch has failed. Replace the switch. Verify that the new switch corrects the diagnostic code. Stop.
NOT OK - The diagnostic code is active in at least one of the positions. Proceed to Test Step 2.Test Step 2. CHECK THE SIGNAL CIRCUITS FOR A SHORT TO GROUND
Turn the key start switch to the OFF position.
Disconnect the machine harness connectors from the ECM.
Measure the resistance between contact J2-38 (wire H480-GN) and frame ground.
Measure the resistance between contact J2-23 (wire H481-PK) and frame ground.Expected Result:The resistances should be greater than 5000 ohms.Results:
OK - The resistances are greater than 5000 ohms.Repair: It is unlikely that the ECM has failed. Exit this procedure and perform this procedure again. If the diagnostic code is still present, replace the ECM. Refer to Testing And Adjusting, "Electronic Control Module (ECM) - Replace". Stop.
NOT OK - The resistance is less than 5000 ohms on one of the readings.Repair: The circuit with the low resistance is shorted in the machine harness. Repair the machine harness or replace the machine harness. Stop.

Caterpillar parts catalog:

Caterpillar parts catalog

Parts plate Caterpillar catalog:

12G, 130G, 140G, 508, 621B, 916, 926, 936, 950B, 950B/950E, 966C, 966D, 980C, CB-414, CB-514, CB-534, CB-614, CP-433B, CS-551, D7H, D8L, D9N, E450, G936, IT18, IT18B, IT28B, PS-110, PS-180, RR-250
1206817 PLATE AS
CB-614, RM-250C, RR-250B
1206818 PLATE AS
CB-614, RM-250C, RR-250B
CB-434, CB-534, CB-614
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.