AVSPARE.COM
parts catalog

PLATE 9V9467 - Caterpillar



9V9467 PLATE Caterpillar parts IT18, IT18F, IT24F, IT28, IT28B, IT28G PLATE
Rating:
70
Alternative (cross code) number:
CA9V9467
9V-9467
9V9467
Caterpillar 9V9467 PLATE
Weight: 97 pounds 43 kg.

Buy PLATE 9V9467 Caterpillar genuine, new aftermarket tractor parts with delivery
INTEGRATED TOOLCARRIER,

Compatible equipment models: 9V9467:

INTEGRATED TOOLCARRIER  IT18   IT18F   IT24F   IT28   IT28B   IT28G   Caterpillar
Number on catalog scheme: 3
 
  For full view, you need register

Information:


Stopping the engine immediately after it has been working under load can result in overheating and accelerated wear of the engine components.Refer to the following stopping procedure, to allow the engine to cool, and to prevent excessive temperatures in the turbocharger center housing, (if equipped) which could cause oil coking problems.
Stopping The Engine From The Operator Compartment
Note: This procedure is used for shutting down both the tractor and the scraper engines. When the scraper engine is shut down from the operator compartment, the tractor engine will be shut down.
Use the procedure that is described in Operation and Maintenance Manual, "Stopping the Machine" in order to stop the machine.
Run the engine at low idle for five minutes. Do not stop the engine immediately after the engine has been working under load.
Illustration 1 g00667031
Turn engine start switch (1) to the OFF position. Remove the engine start switch key. Stopping The Scraper Engine From The Scraper Control
Use the procedure that is described in Operation and Maintenance Manual, "Stopping the Machine" in order to stop the machine.
Run the engine at low idle for five minutes. Do not stop the engine immediately after the engine has been working under load.
Illustration 2 g00667032
Turn engine shutdown switch (2) to the OFF position. This switch is located on the control panel for the scraper.
Illustration 3 g00667024
If Step 3 does not shut down the engine, use the following procedure to shut down the engine. Pull governor control lever (3) for the scraper engine toward the back of the machine to the FUEL-OFF position in order to shut off the engine. This lever is located near the battery disconnect switch. This switch is on the left side of the scraper engine. Note: The governor control lever must be pushed forward to the FUEL-ON position in order to start the scraper engine.

Caterpillar parts catalog:

Caterpillar parts catalog
IT24F Integrated Toolcarrier 6KN00001-UP (MACHINE) POWERED BY 3114 Engine
IT28G Integrated Toolcarrier 9AR00001-01175 (MACHINE) POWERED BY 3116 Engine


Parts plate Caterpillar catalog:

1372135 PLATE AS
IT18F, IT24F, IT28G
7D6104 PLATE
IT18F, IT24F
1226493 PLATE AS
928G, 928HZ, IT24F, IT28G
1364794 PLATE AS
924G, 924GZ, 924H, 924HZ, 928G, 928HZ, 930G, IT14G, IT14G2, IT24F, IT28G
1459377 PLATE-INSTRUCTION
902, 906, 908, 914G, 924G, 924GZ, 924H, 928HZ, 930G, IT14G2, IT24F, IT28F, IT28G
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.