AVSPARE.COM
parts catalog

PLATE AS 9V9892 - Caterpillar



9V9892 PLATE AS Caterpillar parts 916, IT18B PLATE
Rating:
26
Alternative (cross code) number:
CA9V9892
9V-9892
9V9892
Caterpillar 9V9892 PLATE AS
Weight: 7 pounds 3 kg.

Buy PLATE AS 9V9892 Caterpillar genuine, new aftermarket tractor parts with delivery
INTEGRATED TOOLCARRIER, WHEEL LOADER,

Compatible equipment models: 9V9892:

INTEGRATED TOOLCARRIER  IT18B  
WHEEL LOADER  916   Caterpillar
Number on catalog scheme: 17
 
  For full view, you need register

Information:

Towing Procedures
Personal injury or death could result when improperly towing a disabled machine.Block the machine to prevent movement before releasing the brakes. The machine can roll free if it is not blocked.Relieve the hydraulic tank and line pressure before any disassembly. Operate the travel levers back and forth with the engine stopped to relieve pressure.Follow the recommendations below, to properly perform the towing procedure.
To tow the machine, both final drives must be disengaged.Do not operate the travel motors with the final drives disengaged. Damage could result.
These towing instructions are for moving a disabled machine a short distance, only a few feet at low speed, no faster than 2 km/h (1.2 mph), to a convenient location for repair. These instructions are for emergencies only. Always haul the machine if long distance moving is required.Shielding must be provided on the towing machine, to protect the operator if the tow line or bar should break.Do not allow riders on the machine being towed, unless the operator can control the steering and/or braking.Before towing, make sure the tow line or bar is in good condition and has enough strength for the towing situation involved. Use a towing line or bar with a strength of at least 1.5 times the gross weight of the towing machine, for a disabled machine stuck in mud or when towing on a grade.Attach cable to towing eye on front if pulling forward, or attach to drawbar pin if pulling to the rear.Keep the tow line angle to a minimum. Do not exceed a 30° angle from the straight ahead position.Quick machine movement could overload the tow line or bar and cause it to break. Gradual and smooth machine movement will work better.Normally, the towing machine should be as large as the disabled machine. Satisfy yourself that the towing machine has enough brake capacity, weight and power, to control both machines for the grade and distance involved.To provide sufficient control and braking when moving a disabled machine downhill, a larger towing machine or additional machines connected to the rear could be required. This will prevent it from rolling uncontrolled.The different situation requirements cannot be given, as minimal towing machine capacity is required on smooth level surfaces to maximum on inclines or poor surface conditions.Before Towing
1. Lower the implement to the ground with slight down pressure and stop the engine. 2. Operate the travel and control levers to relieve hydraulic line pressure. 3. Loosen the pressure cap to relieve the hydraulic tank pressure. 4. Remove travel drive covers (1) and (2). 5. Clean the areas around the travel motors and brake valves (4).6. Remove four nuts (3) from the travel brake valve. 7. Remove four rods (5), springs (6) and poppets (7).If poppet (7) is difficult to remove, use a magnet. 8. Remove plugs (10). 9. Remove plugs (11). Clean the plugs with nonflammable solution and dry them. 10. Install plugs (10) into the travel brake valves. Tighten the plug until it seats securely. 11. Install grease fittings (13)

Caterpillar parts catalog:

Caterpillar parts catalog
916 WHEEL LOADER 9WB00001-UP (MACHINE) POWERED BY 3204 ENGINE
1T18 INTEGRATED TOOLCARRIER 7ZB00001-UP (MACHINE) POWERED BY 3204 ENGINE
916 WHEEL LOADER 9WB00001-UP (MACHINE) POWERED BY 3204 ENGINE
1T18 INTEGRATED TOOLCARRIER 7ZB00001-UP (MACHINE) POWERED BY 3204 ENGINE
IT18B INTEGRATED TOOLCARRIER 1DF00001-UP (MACHINE) POWERED BY 3204 ENGINE
916 WHEEL LOADER 9WB00001-UP (MACHINE) POWERED BY 3204 ENGINE
1T18 INTEGRATED TOOLCARRIER 7ZB00001-UP (MACHINE) POWERED BY 3204 ENGINE
916 WHEEL LOADER 9WB00001-UP (MACHINE) POWERED BY 3204 ENGINE
1T18 INTEGRATED TOOLCARRIER 7ZB00001-UP (MACHINE) POWERED BY 3204 ENGINE
IT18B INTEGRATED TOOLCARRIER 1DF00001-UP (MACHINE) POWERED BY 3204 ENGINE


Parts plate Caterpillar catalog:

3G5980 PLATE
153, 416, 416B, 426B, 428, 428B, 438B, 446, 446B, 446D, 508, 515, 518, 518C, 525, 525B, 525C, 528, 535B, 535C, 539, 545, 545C, 814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 824C, 826C, 916,...
1P6356 PLATE
1090, 1190, 1190T, 120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 1290T, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 130G, 135H, 135H NA, 1390, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 143H, 14G, ...
2D4202 PLATE
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 12E, 12G, 12H, 12H ES, 12H NA, 12K, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14H, 14H NA, 160G, 160H, 160H ES, 160H NA, 160K, ...
9P7101 PLATE-CLUTCH
910, 916, 926, 926A, 931B, 931C, 931C II, 933, 939, D3C, D3C III, D4B, D4C, D4C III, D4H, D4HTSK II, D5C, D5C III, IT18B, IT28, IT28B
7G7617 PLATE
910, 916, 931B, 931C, 931C II, 933, D3C III, D4B, D4C, D4C III, IT18B
9P6903 PLATE
5110B, 518, 527, 910, 916, 926, 931B, 931C, 931C II, 933, 939, D3C III, D4B, D4C, D4C III, D4H, D4HTSK II, D5C, D5C III, D5HTSK II, IT18B, IT28, IT28B
7G7613 PLATE
910, 916, 926, 926A, 931B, 931C, 931C II, 933, 939, D3C III, D4B, D4C, D4C III, D4H, D4HTSK II, D5C, D5C III, IT18B, IT28, IT28B
6P3843 PLATE-RETAINING
910, 916, 926, 926A, 931B, D4B, D4H, IT18B, IT28
7G0857 PLATE
926, 926A, IT18B, IT28, IT28B
9V3286 PLATE
916, 936, 950F, 966F, IT18B, IT28
7G0824 PLATE-CLUTCH
637E, 69D, 735, 735B, 740, 740B, 768C, 769C, 769D, 770, 771C, 771D, 772, AD40, AD45, AD45B, AD55, AE40, AE40 II, D400E II, RM-350B, SM-350
3T0707 PLATE AS
637E, 69D, 735, 735B, 740, 740B, 768C, 769C, 769D, 770, 770G, 770G OEM, 771C, 771D, 772, 772G, 772G OEM, AD40, AD45, AD45B, AD55, AE40, AE40 II, D400E II
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.