9W0372 PLATE Caterpillar parts PLATE
Rating:
Alternative (cross code) number:
CA9W0372
9W-0372
9W0372
CA9W0372
9W-0372
9W0372
Weight: 2 pounds 1 kg.
Buy PLATE 9W0372 Caterpillar genuine, new aftermarket tractor parts with delivery
Information:
Start By:a. remove flywheel housing 1. Remove plate (1) to remove gear assembly (2) from the shaft 2. Use tool group (A) and a press to remove bearing (3) from gear assembly (2). 3. Remove the bolts to remove the shafts, gears (4) and washers from the cylinder block. 4. Remove washers (6) and shafts (5) from gears (4).5. Use tool group (A) and a press to remove the bearings from gears (4). 6. Remove shaft (7) from the cylinder block. 7. Remove the bolts, and remove gear (8) from the end of the crankshaftInstall Rear Gear Group
1. Put gear (2) in position on the end of the crankshaft, and install the bolts. 2. Install shaft (7) on the cylinder block.3. Use tool group (A) and a press to install the bearing in both gears (4) until the bearings are in the center of their bores. The bore in the bearing must be 75.00 0.053 mm (2.9531 .0021 in) after installation. 4. Put clean engine oil on the bearing, and install shafts (5) in gears (4). Install washers (6) on the shafts.5. Put gears (4) in position on the cylinder block, and install the bolts to hold the gears in position. Tighten the bolts to a torque of 135 15 N m (100 11 lbft). 6. Use tool group (A) and a press to install bearing (3) in gear assembly (2). The bore in bearing (3) must be 75.00 0.053 mm (2.9531 .0021 in) after installation.7. Put clean engine oil on bearing (3) and install gear assembly (2) on shaft (7).8. Put plate (1) in position on gear assembly (2) and install the bolts.End By:a. install flywheel housing
1. Put gear (2) in position on the end of the crankshaft, and install the bolts. 2. Install shaft (7) on the cylinder block.3. Use tool group (A) and a press to install the bearing in both gears (4) until the bearings are in the center of their bores. The bore in the bearing must be 75.00 0.053 mm (2.9531 .0021 in) after installation. 4. Put clean engine oil on the bearing, and install shafts (5) in gears (4). Install washers (6) on the shafts.5. Put gears (4) in position on the cylinder block, and install the bolts to hold the gears in position. Tighten the bolts to a torque of 135 15 N m (100 11 lbft). 6. Use tool group (A) and a press to install bearing (3) in gear assembly (2). The bore in bearing (3) must be 75.00 0.053 mm (2.9531 .0021 in) after installation.7. Put clean engine oil on bearing (3) and install gear assembly (2) on shaft (7).8. Put plate (1) in position on gear assembly (2) and install the bolts.End By:a. install flywheel housing
Parts plate Caterpillar catalog:
9W0315
PLATE-RH
Caterpillar
Caterpillar
9W0233
PLATE-INNER -
Caterpillar
Caterpillar
9W0200
PLATE A
Caterpillar
Caterpillar
9W0120
PLATE
Caterpillar
Caterpillar
9V9788
PLATE-LH
Caterpillar
Caterpillar
9V9787
PLATE A-RH
Caterpillar
Caterpillar
9W0792
PLATE
Caterpillar
Caterpillar
9W0643
PLATE-CENTER
Caterpillar
Caterpillar
9W0642
PLATE-CENTER
Caterpillar
Caterpillar
9W0502
PLATE
Caterpillar
Caterpillar
9W0500
PLATE
Caterpillar
Caterpillar
9W0462
PLATE
Caterpillar
Caterpillar