AVSPARE.COM
parts catalog

PLATE AS 9W0485 - Caterpillar



9W0485 PLATE AS Caterpillar parts D7H PLATE
Rating:
15
Alternative (cross code) number:
CA9W0485
9W-0485
9W0485
Caterpillar 9W0485 PLATE AS
Weight: 0.95 pounds 0 kg.

Buy PLATE AS 9W0485 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK-TYPE TRACTOR,

Compatible equipment models: 9W0485:

TRACK-TYPE TRACTOR  D7H   Caterpillar
Number on catalog scheme: 20
 
  For full view, you need register

Information:


Illustration 1 g02118993
Schematic of the rear axle oil temperature sensor
Sales model 854G\992G
Illustration 2 g01969434
Schematic of the rear axle oil temperature sensor
Sales model 994F
This diagnostic code is associated with the rear axle oil temperature sensor. The FMI 04 means that the ECM has determined that the voltage of the circuit for the sensor is below normal. The pressure sensors are PWM sensors. The PWM signal is dependent on the input pressure and the signal will vary.The possible causes of this diagnostic code are listed below:
The signal circuit for the sensor is shorted to ground.
The sensor has failed.
The ECM has failed. This is unlikely. Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear the diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 0428 FMI 04 is active before performing this procedure. Note: Use the 146-4080 Digital Multimeter for the measurements in this procedure.Test Step 1. CHECK THE SENSOR
Turn the disconnect switch and the key start switch to the ON position.
Ensure that the diagnostic code is active.
Observe the status of the diagnostic code. Disconnect the sensor from the machine harness. Expected Result:The CID 0428 FMI 04 remains active. The FMI has not changed and the "04" is still active.Results:
OK - The diagnostic code remains active. The sensor is correct. Proceed to Test Step 2.
NOT OK - The diagnostic code is no longer active. The sensor has failed.Repair: Replace the sensor.STOPTest Step 2. CHECK THE WIRING HARNESS OF THE SENSOR FOR A SHORT TO GROUND.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness from the sensor.
Disconnect the machine harness connector(s) from the ECM.
At the machine harness connector for the ECM, measure the resistance from the signal contact J2-37 (wire 446-PU(Purple)) of the machine harness to all possible sources of ground. Measure the resistance to all contacts of the machine harness connectors for the ECM. Expected Result:Each resistance measurement is greater than 5000 ohms.Results:
OK - Each resistance measurement is greater than 5000 ohms. The machine harness is correct. Proceed to Test Step 3.
NOT OK - One or more resistance measurements is not correct. There is a short in the machine harness. Repair: The short is between signal contact J2-37 (wire 446-PU(Purple)) and the circuit with the low resistance measurement. Repair the machine harness or replace the machine harness.STOPTest Step 3. CHECK IF THE DIAGNOSTIC CODE REMAINS.
Inspect the contacts of the harness connectors and clean the contacts.
Reconnect all harness connectors.
Turn the disconnect switch and the key start switch to the ON position.
Operate the machine.
Check the status of the CID 0428 FMI 04. Expected Result:The CID 0428 FMI 04 is active. Results:
YES - The CID 0428 FMI 04 is active. The diagnostic code has not been corrected. The ECM may have failed.Repair: It is unlikely that the ECM has failed. Exit this procedure and perform this procedure again. If the cause of the diagnostic code is not found, replace the ECM.

Caterpillar parts catalog:

Caterpillar parts catalog
D7H & D7H LGP TRACTORS / POWER SHIFT / 79Z00001-03999 (MACHINE) POWERED BY 3306 ENGINE
D7H TRACTOR / DIRECT DRIVE / 77Z00001-UP (MACHINE) POWERED BY 3306 ENGINE
D7H & D7H LGP TRACTOR / DIRECT DRIVE / 2SB00001-UP (MACHINE) POWERED BY 3306 ENGINE
D7H TRACK-TYPE TRACTOR / POWERSHIFT / 4AB00001-UP (MACHINE) POWERED BY 3306 ENGINE


Parts plate Caterpillar catalog:

7N7998 PLATE-BLOCK
12G, 12H, 12H ES, 12H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 1673C, 235, 235B, 330, 330 L, 3306, 3306B, 3306C, 330B, 330B L, 350, 528B, 530B, 545, ...
1P6356 PLATE
1090, 1190, 1190T, 120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 1290T, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 130G, 135H, 135H NA, 1390, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 143H, 14G, ...
7N9342 PLATE-THRUST
120G, 12G, 130G, 140B, 140G, 14G, 160H, 1673C, 215, 235, 3204, 330 L, 3304, 3304B, 3306, 3306B, 330B, 350, 518, 528, 561D, 571G, 572G, 627B, 637D, 639D, 815, 816, 916, 920, 926, 930, 931B, 936F, 941, ...
5S1213 PLATE
120, 120B, 12F, 140, 140B, 14E, 16, 16G, 245, 245B, 245D, 3304B, 3306, 5130, 5130B, 5230, 5230B, 561B, 561C, 572G, 578, 589, 594H, 613, 621, 621B, 621E, 621F, 621R, 623, 623E, 623F, 627, 627B, 627E, 6...
9W8269 PLATE-REACTION
572R, 578, 583R, 814B, 815B, 980C, 980F, 980F II, 980G, 980H, D6R, D6R II, D6R III, D7H, D7R, D7R II, D8N, D8R II, D8T
7T7305 PLATE
589, D10N, D10R, D10T, D10T2, D11N, D11R, D11T, D7H, D7R, D7R II, D7R XR, D8N, D8R, D8R II, D8T, D9N, D9R, D9T
6P5404 PLATE-CLUTCH & BRAKE
589, D6H, D7H, D8L, D9L
6T0243 PLATE-THRUST
578, 589, D10N, D6H, D7H, D8L, D9L, D9N
6T3080 PLATE-CLUTCH & BRAKE
578, D6H, D6H XL, D7H
2P4370 PLATE-CLUTCH
55, 57, 578, 58, 594H, D10N, D10R, D5B, D6D, D6H, D6H II, D6H XL, D6H XR, D7G, D7H, D7R, D8L, D8N, D8R, D9L, D9N
9G4521 PLATE AS-LOCKING
D10, D11N, D4H, D5H, D6H, D6H XL, D6H XR, D7H, D8L, D9L
4B1382 PLATE-SPRING CAP
127, 561B, 561C, 844, 844H, 844K, 951B, 955C, 955H, 955K, 955L, 977D, 990, 990 II, 990H, 990K, D5, D5B, D5E, D6C, D6D, D6E, D6E SR, D6G, D6G SR, D6G2 LGP, D6G2 XL, D7H, D9R
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.