AVSPARE.COM
parts catalog

PLATE 9W0502 - Caterpillar



9W0502 PLATE Caterpillar parts PLATE
Rating:
86
Alternative (cross code) number:
CA9W0502
9W-0502
9W0502
Caterpillar 9W0502 PLATE
Weight: 443 pounds 200 kg.

Buy PLATE 9W0502 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

15. Disconnect hoses (31) and (32) from the air starter. 16. Disconnect ground wire (33) from the frame. 17. Turn the fuel supply off at fuel tank shut-off valve (34). 18. Disconnect hose assembly (36) from fuel transfer pump (38).19. Disconnect hose assembly (37) from transmission oil cooler (35). 20. Disconnect the fuel return hose assembly from fitting (39). Put a cap on fitting (39). 21. Loosen two hose clamps and remove hose (40) from the transmission oil cooler.22. Loosen the hose clamps and disconnect hoses (41) and (42) from the valve assemblies. 23. Loosen two hose clamps and disconnect hose (43) from tube (44).24. Disconnect hose assembly (45) from the brake oil cooler. 25. Disconnect hose assembly (46) from tube assembly (47). 26. Disconnect hose assembly (48) from the brake oil cooler.27. Remove bolt and clamp (49) and disconnect hose assembly (50) from the brake oil cooler.28. Remove the bolt and clamp that fastens hose assembly (48) to the front of the torque converter housing. 29. Remove hose assembly (52) from elbow (53) and diverter valve (51). Loosen the hose clamps and remove hose (54). 30. Disconnect hose assembly (55) from elbow (53). Disconnect hose assembly (56) from the spacer. 31. Disconnect hose assembly (57) from the torque converter inlet relief valve.32. Disconnect hose assemblies (58) and (59) from the torque converter housing.33. Disconnect hose assemblies (61) and (62) from torque converter oil pump (63).34. Disconnect hose assembly (60) from the parking brake release section of pump (63). 35. Disconnect hose assembly (64) from pump (63).36. Disconnect hose assemblies (65) and (66) from the brake cooling section of pump (63). 37. Disconnect hose assemblies (68), (69) and (71) from the lockup clutch valve.38. Disconnect hose assembly (70) from the torque converter housing.39. Remove main driveshaft guard (67). 39. Disconnect cable (72) from the tackometer drive. 40. Remove fitting (73) and loosen the collar at the rear of yoke assembly (74), (part of main drive shaft).41. Remove the bolts that hold spider and bearing assembly (75) to the torque converter yoke.42. Slide yoke assembly (74) away from the torque converter yoke. 43. Remove the bolts that hold drive shaft guard (77) and remove drive shaft guard (77).44. Remove bolts (78) and disconnect drive shaft (76), (auxiliary drive shaft). 45. Remove nuts (80), washers and bolts that hold caps (79) in position. Remove caps (79) from both of the rear engine supports. 46. Remove ground strap (81) from the engine front support. 47. Remove nuts, washers and bolts (83). Remove top cushions (82) from both sides of engine front support (84). 48. Fasten a hoist to the engine. Remove the engine and torque converter, from the truck. The weight of the engine and torque converter is approximately 8,375 kg (18,500 lb). The following steps are for installing the engine and torque converter 49. Fasten a hoist to the engine. Put lower cushions (82) in position in engine front support (84). Put the engine and torque converter in position in


Parts plate Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.