AVSPARE.COM
parts catalog

PLATFORM AR 3534630 - Caterpillar



3534630 PLATFORM AR Caterpillar parts 772G PLATFORM
Rating:
13
Alternative (cross code) number:
CA3534630
353-4630
3534630
Caterpillar 3534630 PLATFORM AR

Buy PLATFORM AR 3534630 Caterpillar genuine, new aftermarket tractor parts with delivery
TRUCK,

Compatible equipment models: 3534630:

TRUCK  772G   Caterpillar
  For full view, you need register

Information:


Illustration 23 g01364771
Use template (1) in order to put segment (2) in the correct position. Use clamps to hold the segment in place.Note: The template is used for alignment purposes only and should not be used as a tooth profile gauge. The template tooth profile does not match the segment or circle teeth profile.
Illustration 24 g01364776
Illustration 25 g01364778
Illustration 26 g01364779
Tack weld the end faces of teeth (4), as shown. Tack weld segment (2) to the circle with three tack welds on the top and three tack welds on the bottom. Use the template to check the position of segment (2) .
Illustration 27 g01364793
Repeat Step 6 through Step 13 in order to install each additional segment. After all segments have been installed, check each segment again with the template. Check if the diameter of the circle is within the tolerance that was given in Step 5.
Illustration 28 g01364798
Place the circle in a level position. Use low heat and weld segments one, three, five, two, and four in this order with small welds. Do not weld the end of the teeth of the segments at this time. Any additional teeth that have been changed should be welded in the same sequence. Refer to Illustrations 1 through 3.
Illustration 29 g01364802
Turn over the circle and place the circle in a level position. Use low heat and weld segments one, three, five, two, and four in this order with small welds. Do not weld the end of the teeth of the segments at this time. Any additional teeth that have been changed should be welded in the same sequence. Refer to Illustrations 1 through 3.
Illustration 30 g01364806
Make a 6.0 mm (0.25 inch) continuous bevel groove weld across all of the segments. Be sure that the weld does not extend into the wear surface. Check the welds for cracks. Remove any cracks with an Arcair torch. Weld the grooves. Remove all weld splatter.
Illustration 31 g01364816
Turn over the circle and place the circle in a level position. Make a 6.0 mm (0.25 inch) continuous bevel groove weld across all the segments. Be sure that the weld does not extend into the wear surface. Check the welds for cracks. Remove any cracks with an Arcair torch. Weld the grooves. Remove all weld splatter.
Illustration 32 g01364818
Illustration 33 g01364820
View showing the grooves of the tooth.
Weld the grooves on the end of the teeth and grind the welds until the welds are flat and smooth. Remove all weld splatter from the circle.
Illustration 34 g01364848
Right view
Illustration 35 g01364849
Left view
Illustration 36 g01364857
Detailed view
Turn over the circle and place the circle in a level position. Weld the end of the teeth. First weld the top grooves of the end of teeth (4). Next weld the inner faces of end of teeth (4). Grind all the welds until the welds are flat and smooth. Remove all weld splatter.
Install the circle. Refer to the Service Manual. Check the operation of the circle.

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
772G Off-Highway Truck LTS00001-UP (MACHINE) POWERED BY C18 Engine
772G OEM Off-Highway Truck RMH00001-UP (MACHINE) POWERED BY C18 Engine
772G OEM Off-Highway Truck TWB00001-UP (MACHINE) POWERED BY C18 Engine


Parts platform Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.