AVSPARE.COM
parts catalog

PLATFORM AS 9W0543 - Caterpillar



9W0543 PLATFORM AS Caterpillar parts D6H, D6H XL, D6H XR, D7H, D8N PLATFORM
Rating:
32
Alternative (cross code) number:
CA9W0543
9W-0543
9W0543
Caterpillar 9W0543 PLATFORM AS
Weight: 313 pounds 141 kg.

Buy PLATFORM AS 9W0543 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK-TYPE TRACTOR,

Compatible equipment models: 9W0543:

TRACK-TYPE TRACTOR  D6H   D6H XL   D6H XR   D7H   D8N   Caterpillar
Number on catalog scheme: 1
 
  For full view, you need register

Information:


Illustration 1 g01249391
Schematic of the torque converter output speed sensorThis diagnostic trouble code is associated with the torque converter output speed sensor. The FMI "08" means that the ECU has determined that the signal frequency or the signal pulse width is not within the expected range. The possible causes of this diagnostic trouble code are listed below:
The sensor has failed.
Intermittent connections or poor connections
Mechanical devices are loose.
The ECU has failed. This is unlikely.Note: The following test procedure may create other diagnostic trouble codes. Ignore these created diagnostic trouble codes and clear the diagnostic trouble codes when the original diagnostic trouble code has been corrected. Ensure that the diagnostic trouble code of CID 0672 FMI 08 is active before performing this procedure. The engine must be running in order for the diagnostic trouble code to be active.Note: Use a digital multimeter for the measurements in this procedure. Test Step 1. CHECK THE SENSOR.
Turn the disconnect switch and the key start switch to the ON position.
Ensure that the diagnostic trouble code is active.
Disconnect the sensor from the machine harness.Expected Result:The diagnostic trouble code is NO longer active.Results:
OK - The diagnostic trouble code is NO longer active. The sensor has failed. Repair: Replace the sensor. Verify that the new sensor corrected this diagnostic trouble code. The diagnostic trouble code is NOT active.STOP
NOT OK - The diagnostic trouble code remains active. The sensor is not the cause of the diagnostic trouble code. Proceed to Test Step 2.Test Step 2. CHECK FOR A SHORT IN THE HARNESS.
The sensor remains disconnected from the machine harness.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the J1 and J2 machine harness connectors from the transmission ECU.
At the J1 machine harness connector for the ECU, measure the resistance between the signal contact J1-4 (wire L910-PK) to all other J1 and J2 contacts.Expected Result:Each resistance measurement is greater than 5000 ohms.Results:
OK - The resistance that is measured is greater than 5000 ohms for each measurement. The harness is correct. The ECU may have failed. Proceed to Test Step 3.
NOT OK - The resistance that is measured is NOT greater than 5000 ohms for each measurement. The machine harness has failed.Repair: There is a short in the machine harness. The short is between the signal circuit (wire L910-PK) and the circuit with the low resistance measurement. Repair the machine harness or replace the machine harness.STOPTest Step 3. CHECK IF THE DIAGNOSTIC TROUBLE CODE REMAINS
Inspect the harness connectors. Clean the contacts of the harness connectors and check the wires for damage to the insulation that is caused by excessive heat, battery acid, or chafing.
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the circuit.
Reconnect all harness connectors in order to make sure that the connectors are fully seated. Also, make sure that the clips for each connector are completely fastened.
Turn the disconnect switch and the key start switch to the ON position.
Operate the vehicle.
Check the status of the CID

Caterpillar parts catalog:

Caterpillar parts catalog
D8N TRACTOR 9TC00001-UP (MACHINE) POWERED BY 3406 ENGINE
D7H & D7H LGP TRACTORS / POWER SHIFT / /DIFFERENTIAL STEERIN/ 4FG00001-03999 (MACHINE) POWERED BY 3306 ENGINE
D6H, D6H LGP TRACTORS DIFFERENTIAL STEERING 3YG00001-03999 (MACHINE) POWERED BY 3306 ENGINE
D7H & D7H LGP SERIES II TRACTORS / POWERSHIFT / 79Z04000-UP (MACHINE) POWERED BY 3306 ENGINE
D6H XR SERIES II TRACK-TYPE TRACTOR / POWER SHIFT / 5KK00001-UP (MACHINE) POWERED BY 3306 ENGINE
D6H XR SERIES II TRACTOR / POWER SHIFT / 2BL00001-UP (MACHINE) POWERED BY 3306 ENGINE
D6H D6H LGP Series II Track-Type Tractors 5HF04000-UP (MACHINE) POWERED BY 3306 Engine
D6H Series II Track-Type Tractor Direct Drive 1FJ04000-UP (MACHINE) POWERED BY 3306 Engine
D6H Series II XL Track-Type Tractor Power Shift 8ZJ00001-UP (MACHINE) POWERED BY 3306 Engine
D6H Track-Type Tractor XL 9KJ00001-UP (MACHINE) POWERED BY 3306 Engine
D6H XL Series II Track-Type Tractor 9LK00001-UP (MACHINE) POWERED BY 3306 Engine
D6H XR Series II Track-Type Tractor Differential Steering 1YL00001-UP (MACHINE) POWERED BY 3306 Engine


Parts platform Caterpillar catalog:

8G5658 PLATFORM AS
D4H, D5H, D5H XL
1564757 PLATFORM AS
D6R II, D7R II, D8R II
1353970 PLATFORM AS
315B FM L, 320B FM LL
1491801 PLATFORM AS
315B FM L, 320B FM LL
9U8252 PLATFORM AS
D4H, D4H XL, D5H
9W9505 PLATFORM AS
D6H, D6H XL, D6H XR, D7H, D8N, D9N
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.