AVSPARE.COM
parts catalog

PULLER GP-PIN 4Z8946 - Caterpillar



4Z8946 PULLER GP-PIN Caterpillar parts D10R, D10T, D10T2 PULLER
Rating:
75
Alternative (cross code) number:
CA4Z8946
4Z-8946
4Z8946
Caterpillar 4Z8946 PULLER GP-PIN
Weight: 24 pounds 11 kg.

Buy PULLER GP-PIN 4Z8946 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK-TYPE TRACTOR,

Compatible equipment models: 4Z8946:

TRACK-TYPE TRACTOR  D10R   D10T   D10T2   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:

For 6V50 Engine Timing Indicator, refer to the topic CALIBRATION PROCEDURE in Special Instruction Form SEHS8135, "ELECTRONIC REPAIR OF 6V3100 ENGINE TIMING INDICATOR".1. Refer to the topic CALIBRATION USING A FREQUENCY COUNTER, and use 8T5201 Signal Generator/Counter (1) in place of the frequency counter. Use 8T5112 Signal Input Cable (2) to connect the unit that is to be calibrated to the INPUT connection on signal generator/counter (1).2. In the alternate procedure, CALIBRATION USING A 5P9698 CALIBRATOR, the 5P9698 Calibrator must be used for these adjustments. The calibration procedure cannot be done with total accuracy if the 8T5201 Signal Generator/Counter is used as a replacement for 5P9698 Calibrator.Checking The 6V6113 Amplifier From The 6V4950 Injection Line Speed Pickup Group
1. Refer to the topic, CHECKING THE 6V6113 AMPLIFIER in Special Instruction Form SEHS8029.2. Follow the instructions given within the above topic except, use 6V6152 Adapter Plug (1) and 8T5197 Calibrator Cable (2) to connect CAL OUT on 8T5201 Signal Generator/Counter (3) to 6V6113 Amplifier (4). (8T5201 Signal Generator/Counter is being used instead of 5P9698 Calibrator.)3. Turn on the power and set the 8T5201 Signal Generator/Counter to exactly 25 Hz, with no change on the LCD reading.4. Program the multitach P/REV number for 30. (The multitach will display 50 1 rpm instead of 3000 rpm.)5. Do the remainder of the procedure as given in CHECKING THE 6V6113 AMPLIFIER.Operational Checks
The 8T5201 Signal Generator/Counter can be used instead of the 5P9698 Frequency Calibrator to perform an operational check of the 5P3600 Hydraulic Flow Meter, or the 1P5500 Photo Tach. Connect the 8T5197 Calibrator Cable, with the correct adapter, to the CAL OUT connection. Use the Special Instruction Form, for the unit being tested, to perform the operational check. If an accurate calibration is needed, use the 5P9698 Frequency Calibrator for the calibration procedure.Using The 8T5201 Signal Generator/Counter As A Frequency Counter
1. Connect 8T5112 Cable (1) to the input connection on the 8T5201 Signal Generator/Counter (2).2. Push the ON switch to turn on power to the 8T5201 Signal Generator/Counter.3. Connect a signal source, as shown, (pulsating DC or AC) to the 8T5112 Cable, from 10-19999 Hz and from .1 V-50 Volt maximum. The display will read the input signal 1 Hz. The readout can display from 1-19999, but the Overrange Arrow will be visible for readings from 9999 to 19999 Hz. This should be remembered when it is known that the reading will be in the 9999-19999 Hz range. The counter has the capacity to count above 19999, but cannot display a higher number. Any reading above 19999 will be displayed as a number between 10,000 and 19,999, i.e., a reading of 24550 Hz will be displayed as 14550 Hz, and the overrange arrow will be visible.4. Since the 8T5201 Signal Generator/Counter uses internal batteries, turn it OFF when it is not in use. Battery life expectancy is approximately 80 hours on the two alkaline batteries. A "LO BAT" indication will appear on the display when it is necessary to replace the

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
D10R Custom Parts Manual Track-Type Tractor 3KR00001-UP (MACHINE)
D10R CUSTOM PARTS MANUAL TRACK-TYPE TRACTOR AKT00001-UP (MACHINE) POWERED BY 3412E Engine
D10T TRACK-TYPE TRACTOR RJG00001-UP (MACHINE) POWERED BY C27 Engine
D10T2 TRACK-TYPE TRACTOR JJW00001-UP (MACHINE) POWERED BY C27 Engine
D10T2 TRACK-TYPE TRACTOR RAB00001-UP (MACHINE) POWERED BY C27 Engine


Parts puller Caterpillar catalog:

2024327 PULLER-FUSE
525C, 535C, 545C, 561N, 613G, 621G, 623G, 627G, 631G, 637G, 657G, 725, 730, 735, 740, 770, 772, 773F, 775F, 777F, 793F, 793F CMD, 793F-XQ, 795F AC, 797F, 824G II, 824H, 825G II, 825H, 826G II, 826H, 8...
1355111 PULLER GP-PIN
D8R, D8R II, D8T, D9R, D9T
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.