parts catalog

PULLEY 3B9313 7B0257 - Caterpillar

7B0257 PULLEY 3B9313 Caterpillar parts PULLEY
Alternative (cross code) number:
Caterpillar 7B0257 PULLEY 3B9313

Buy PULLEY 3B9313 7B0257 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register


Illustration 1 g01209718
Brake cooling pump solenoid connections
This diagnostic code is associated with the brake cooling pump solenoid. The FMI 03 means that the ECM has determined that the voltage of the solenoid circuit is above normal.Some possible causes of the diagnostic code are listed:
The solenoid has failed.
The energize circuit of the solenoid is shorted to the +battery circuit.
The ECM has failed. This is unlikely.System Response:When the CID 1230 FMI 03 diagnostic code is active, the machine response can be:
The ECM will not control the differential cooling fan
The differential cooling fan may run at maximum speed when the key switch is ON.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 1230 FMI 03 is active before performing this procedure.Test Step 1. CHECK THE ENERGIZE CIRCUIT OF THE SOLENOID FOR A SHORT TO THE +BATTERY CIRCUIT
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness connector from the solenoid. Disconnect the machine harness connectors J-1 and J-2 from the ECM.
At the machine harness ECM connector J2, measure the resistance from contact J2-8 (wire J817-WH(White)) to all J-1 and J-2 contacts that are connected to +battery. The J-1 +battery contacts are J1-1, J1-6, J1-28 and J1-40. No J-2 contacts are connected to +battery. Expected Result:Each resistance measurement is greater than 5000 ohms. Results:
OK - Each resistance measurement is greater than 5000 ohms. The machine harness is correct. Proceed to Test Step 2.
NOT OK - Each resistance measurement is not greater than 5000 ohms. There is a short in the machine harness. The short is between J2-8 (wire J817-WH(White)) and the circuit that has a low resistance measurement. Repair: Repair the machine harness or replace the machine harness.STOPTest Step 2. CHECK IF THE DIAGNOSTIC CODE IS STILL ACTIVE
Inspect the contacts of the harness connectors that are used in the solenoid circuit. Ensure that the contacts are secure. Clean all of the contacts in the harness connectors.
Reconnect all harness connectors.
Turn the disconnect switch and the key start switch to the ON position.
Operate the machine.
Determine if the CID 1230 FMI 03 code is active. Expected Result:The CID 1230 FMI 03 code is active.Results:
YES - The CID 1230 FMI 03 code is active.Repair: Repeat this procedure. If the problem remains, replace the solenoid. After the solenoid is replaced, repeat this Test Step again. If the diagnostic code is still active, the ECM may be faulty. It is unlikely that the ECM has failed. Exit this procedure and perform this procedure again. If the cause of the diagnostic code is not found, replace the ECM. See Testing and Adjusting, "Electronic Control Module (ECM) - Replace".STOP
NO - The CID 1230 FMI 03 code is not active. The problem does not exist at this time.Repair: The initial diagnostic code was probably caused by a poor electrical connection or a short at one of the harness connectors that

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.