AVSPARE.COM
parts catalog

PUMP GP 3599608 - Caterpillar



3599608 PUMP GP Caterpillar parts PUMP
Rating:
66
Alternative (cross code) number:
CA3599608
359-9608
3599608
Caterpillar 3599608 PUMP GP
Weight: 160 pounds 72 kg.

Buy PUMP GP 3599608 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

Start By:a. remove fuel lines 1. Use tool (F) and remove the shutdown solenoid (1). 2. Remove two bolts (2) and remove actuator solenoid (3) from the fuel injection pump housing.3. Remove two rack zero plugs (4).
Typical Example4. Push the rack servo (5) toward the rear of the engine. Install tools (A) in the rack zero pin holes. Push the rack servo (5) toward front of the engine and install tool (B) to hold the rack against the rack zero pin. 5. Use tool (C) to loosen bushing (6). 6. Install tool (E) and compress fuel pump spring. Hold tool (E) in position and remove bushing (6).
Typical Example7. Remove fuel injection pump with tool (D).
When injection pumps, spacers, and lifters are removed from the injection pump housing, keep the parts of each pump together so they can be installed back in their original location.
8. Disassemble the fuel injection pump. Remove ring (8). Make a separation of bonnet (7) from the plunger and barrel assembly (9).
Be careful when the injection pumps are disassembled. Do not cause damage to the surface on the plunger. The plunger and barrel for each pump are made as a set. Do not put the plunger of one pump in the barrel of another pump. If one part has wear, install a complete new pump assembly. Be careful when the plunger is put into the bore of the barrel.
9. Remove the gear segment, the washer, and the spring from the barrel.10. Remove the ring, spring, the collar, and valve from the barrel.
Typical Example11. Remove spacer (10).Install Fuel Injection Pumps
Typical Example Make sure the fuel racks are in the center (zero) position before the fuel injection pumps are installed.1. Install plunger (10) and gear segment (11), washer (5), and spring (9) in position on barrel (4). Put check valve assembly (7), spring (3), and collar (8) in position in bonnet (6). Connect bonnet (6) and barrel (4) together with ring (2). Keep seal (1) with bonnet for use during installation. 2. Put spacer (13) into position in the pump housing bore. Make sure the correct spacer is with each pump.3. Align the space in gear segment (11) with the groove in barrel (4).4. Put the injection pump straight down into the housing bore so the space in gear segment (11) aligns with pin (12) and the groove in barrel (4) aligns with dowel (14). Use tool (C) to install the pump. 5. Install seal (1) and bushing (16) in the pump housing bore. If the pump is in the correct position, install tool (D) with bushing (16). Compress fuel injection pump spring with tool (D) and hand start the bushing threads into the pump housing. Tighten the bushing to a torque of 245 15 N m (180 10 lb ft) with tool (B).6. Check for correct installation of the injection pumps with the engine stopped. See the topic, Injection Pump Installation in the Testing and Adjusting manual.
If one or more of the injection pumps


Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.