parts catalog

PUMP GP-ENGINE OIL 3967058 - Caterpillar

3967058 PUMP GP-ENGINE OIL Caterpillar parts
Alternative (cross code) number:
Caterpillar 3967058 PUMP GP-ENGINE OIL

Buy PUMP GP-ENGINE OIL 3967058 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme:
  For full view, you need register


Illustration 1. New hose press frame and optional items.6V4880 Hose Press Frame
The 6V4880 Hose Press Frame (Illustration 1) is the "press" part of the 6V4900 Hose Press Arrangement. It is similar to the former 5S2801 Hose Press Frame but has: - a longer stroke- a larger opening between tie rods- wider tooling openings between the fixed (can not be moved) and movable (can be moved) bolsters. With the former hose press frame it was possible for tooling or hose components to get in the way when the movable bolster was retracted.- a guard that is part of the clamping bar and screw (Illustration 2). The front tooling can no longer be clamped (held in position) without use of the guard as was possible with the former hose press.
Illustration 2. Location of shield and clamping screw in 6V4880 Hose Press Frame.Both the new and former hose press frame have a 445 kN (50 ton) capacity. No tooling comes with the 6V4880 Hose Press Frame if it is ordered by itself.
6V4860 XT-5 Tool Group
To fabricate or recondition XT-5 hose assemblies, the 6V4860 Tool Group is needed, in addition to the 6V4880 Hose Press Frame and many tools from the 6V4900 Hose Press Arrangement. Included in the 6V4860 Tool Group are special hose remover tools for 19 mm (.75") I.D. and 25.4 mm (1.00") I.D. XT-5 hose (Illustration 3). These two sizes of XT-5 hose are the most difficult to remove from the coupling, when the coupling is to be used again. Use of these tools is explained in Special Instruction, "Use of 6V4900 Hydraulic Service Press Arrangement," Form SEHS7957-01. A complete list of part numbers for the 6V4860 Tool Group is available in the Caterpillar Tool Guide.
Illustration 3. Remover tool for XT-5 hose.6V4974 Hose Press Stand
Because the new 6V4880 Hose Press is larger than the former hose press in almost all dimensions, it is not practical to install on a standard work bench. The new 6V4974 Hose Press Stand permits the hose press to be taken off the workbench and put anywhere in the shop. The foot switch and hydraulic pump can be fastened to the press stand, as shown in Illustration 4. Since the area under the stand is open, tooling and hose components can not fall between the bolsters and get in the way. If desired, the 6V4974 Hose Press Stand can be fabricated according to FT1643 drawings, available from your Division Service Manager. The hardware which follows is needed for assembly of either stand:
4 - 6F7032 Bolt (to fasten the hydraulic pump to stand)14 - S509 Bolt12 - 1D4717 NutWhen the 6V4880 Hose Press Frame is fastened to the 6V4974 Hose Press Stand along with a new hydraulic pump, use the parts which follow to connect the pump to the press:
2 - 9P9506 XT-3 Hose Assembly4 - 8L3282 AdapterA pressure gauge can be installed on the hose press so hydraulic oil pressure can be noted during assembly and disassembly of hose couplings. See Illustration 5.
Illustration 4. The

Caterpillar parts catalog:

Caterpillar parts catalog
G3520H Generator Set GFP00001-UP
G3520H Generator Set GFR00001-UP
G3520 Generator Set E2J00001-UP
G3520 Generator Set E2K00001-UP
G3520 Generator Set E2800001-UP
G3520 Generator Set E2900001-UP

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.