AVSPARE.COM
parts catalog

PUMP & MTG GP-STEERING 4646301 - Caterpillar



4646301 PUMP & MTG GP-STEERING Caterpillar parts PUMP
Rating:
56
Alternative (cross code) number:
CA4646301
464-6301
4646301
Caterpillar 4646301 PUMP & MTG GP-STEERING

Buy PUMP & MTG GP-STEERING 4646301 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 4
 
  For full view, you need register

Information:

Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 0V-0375 Bolt 1
5P-8245 Hard Washer 1 Start By:
Install the lifting brackets on the engine. Refer to Disassembly and Assembly, "Engine Lifting Bracket - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00921920Note: Mark the positions of supports (4) and shims (5). The engine supports on the right side are attached to plates (6) on the generator base by dowels (1). Dowels (1) must be removed before the mounting supports can be removed.
Use Tooling (A) to remove dowels (1).
Attach a suitable lifting device to the lifting brackets. The weight of the six cylinder engine is approximately 15 650 kg (34,500 lb). The weight of the eight cylinder engine is approximately 20 412 kg (45,000 lb). Note: The weight is ONLY for the engine.
Loosen bolt (2).
Remove bolts (3) that hold the engine supports to the base.
Lift the engine enough in order to place a nylon strap around the support. The weight of each support is approximately 64 kg (141 lb).
Illustration 2 g00921919
Remove bolts (8) that hold the support (4) to the cylinder block.
Tap support (4) with a large plastic hammer in order to disengage dowels (7) from the cylinder block.
Remove support (4) from the side of the cylinder block.
If necessary, remove dowels (7) from engine support (4). Installation Procedure
Illustration 3 g00921919
If dowels (7) were removed from support (4), install dowels (7). Dowels (7) should extend 20.0 1.0 mm (0.79 0.04 inch) above the surface of support (4).
Put the support in the correct position on the cylinder block. Install the bolts (8). Tighten the bolts to a torque of 1125 100 N m (830 75 lb ft).
Illustration 4 g00921920
Install shims (5) in the regular location.
Lower the engine onto plates (6). Install bolts (3).
Install dowels (1) through engine support (4) and into plate (6) on the right side of the engine.
Check the alignment between the engine and the driven equipment. End By:
Remove the lifting brackets from the engine. Refer to Disassembly and Assembly, "Engine Lifting Bracket - Remove and Install".

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
794 AC Off-Highway Truck MN500001-UP (MACHINE) POWERED BY C175-16 Engine
794 AC OFF-HIGHWAY TRUCK HRZ00001-UP (MACHINE) POWERED BY C175 ENGINE
798AC OFF-HIGHWAY TRUCK ST300001-UP (MACHINE) POWERED BY C175 ENGINE


Parts pump Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.