AVSPARE.COM
parts catalog

RETAINER 1C4165 - Caterpillar



1C4165 RETAINER Caterpillar parts PR-1000, PR-450, PR-450C, PR-750B RETAINER
Rating:
30
Alternative (cross code) number:
CA1C4165
1C-4165
1C4165
Caterpillar 1C4165 RETAINER
Weight: 0.76 pounds 0 kg.

Buy RETAINER 1C4165 Caterpillar genuine, new aftermarket tractor parts with delivery
COLD PLANER,

Compatible equipment models: 1C4165:

COLD PLANER  PR-1000   PR-450   PR-450C   PR-750B   Caterpillar
Number on catalog scheme: 7
 
  For full view, you need register

Information:

If the detection area is to narrow or contains holes in the coverage area, the angles of the brackets of the object detection sensors. Refer to the "Adjust the Object Detection Sensors" section of this manual for additional information regarding the adjustment of the brackets.Note: If the detection area is larger than the dimensions listed above, adjustment of the object detection sensors is not required.Operate the machine to determine if more adjustment is required.Right Side and Left Side of the Machine
Lay out a line perpendicular to the centerline of the radar. Extend the line 6 m (20 ft). Lay out extra lines parallel to the centerline of the radar. Lay out lines at the following intervals:
0.5 m (1.5 ft)
1 m (3 ft)
1.5 m (5 ft)
3 m (10 ft)
5 m (16 ft)The object will be moved close to the machine and parallel to the side of the machine and the display is checked for the object detection. The object will then be moved perpendicular to the rear of the machine as shown in Illustration 131. The object should start close to the machine for the first pass and work away from the machine with each successive pass. Stop the passes once the object is no longer detected.This pattern will be completed on both sides of the machine. The target should start outside of the detection range of the radar. The target will walk parallel to the machine and stop whenever the target appears in the radar detection area.
Illustration 131 g02728232
Target moving on side of machine
The person in the cab of the machine will inform the person moving the object when to mark the coverage start/stop point. The start/stop points must be marked when the object first appears or first disappears from radar coverage on the display. The designated reference point for the rear radar will be the center of the machine. The distance from the initial perpendicular detection must be measured and should be approximately 0.3 m (1.0 ft) from the rear of the machine. Refer to Illustration 132.
Illustration 132 g02728236
A sample of right side and left side machine target detection
If the detection area is to narrow or contains holes in the coverage area, the angles of the brackets of the object detection sensors. Refer to the "Adjust the Object Detection Sensors" section of this manual for additional information regarding the adjustment of the brackets.Note: If the detection area is larger than the dimensions listed above, adjustment of the object detection sensors is not required.Operate the machine to determine if more adjustment is required.Camera View
Illustration 133 g01223051
Camera
Illustration 134 g02351878
Typical example of the proper orientation of the image from front camera on the monitor
Front camera is set up by the factory or by a Caterpillar dealer to provide the following view from the machine front:
Partial view of the radiator grills
Partial view of the stairs
View of an object on the ground in front of the stairs
Illustration 135 g02351896
Typical example of the proper orientation of the image from rear camera on the monitor
The dump body is shown

Caterpillar parts catalog:

Caterpillar parts catalog
PR-450C Cold Planer 7PJ00001-UP (MACHINE) POWERED BY 3408 Engine


Parts retainer Caterpillar catalog:

8C0828 RETAINER
PR-450, PR-450C
1G7366 RETAINER
AP-1055D, AP-200B, AP-600D, AP-655C, AP-655D, AP1000E, AP1055E, AP555E, BG-2455D, BG-260D, BG1000E, BG1055E, BG500E, BG600D, BG655D, CP-433C, CS-323C, CS-431C, CS-433C
1G7363 RETAINER
AP-1055D, AP-200B, AP-600D, AP-655C, AP-655D, AP1000E, AP1055E, AP555E, BG-2455D, BG-260D, BG1000E, BG1055E, BG500E, BG600D, BG655D, CB-334D, CB-334E, CB-335D, CP-433C, CP-433E, CP-44, CS-323C, CS-423...
0304041 RETAINER
PR-105, PR-450, PR-450C
0092041 RETAINER
CB-614, CS-551, PR-450, PR-450C, SS-250
7R8469 RETAINER-SEAL
PR-105, PR-450, PR-450C
0778365 RETAINER
AP-800, CB-614, CS-551, PR-450C, RR-250, SS-250
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.