AVSPARE.COM
parts catalog

RING-THRUST 4644981 - Caterpillar



4644981 RING-THRUST Caterpillar parts RING
Rating:
86
Alternative (cross code) number:
CA4644981
464-4981
4644981
Caterpillar 4644981 RING-THRUST
Weight: 308 pounds 139 kg.

Buy RING-THRUST 4644981 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 1 g01321608
Connections of the air temperature switchThis diagnostic code is associated with the air temperature switch. This diagnostic code is recorded when the ECM reads the signal from the switch and the ECM determines that the signal is erratic, intermittent, or incorrect.The possible causes of this diagnostic code are listed:
An open circuit exists.
The ECM has failed. This is unlikely.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear the diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 2659 FMI 02 is active before performing this procedure.Note: Use a digital multimeter for the measurements in this procedure.Test Step 1. VERIFY THE SOFTWARE VERSIONNote: Check and record the latest software version for the machine electronic controls from SIS.
Verify that the latest version of software has been loaded to the Machine ECM.Expected Result:All of the software is current.Results:
OK - All of the software is current. Proceed to Test Step 2.
NOT OK - There is a more recent software release that is available.Repair: Flash all controls with the latest software release. Refer to Troubleshooting, "Electronic Control Module (ECM) - Flash Program".STOPTest Step 2. CHECK THE HARNESS.
Turn the key start switch to the OFF position.
Inspect the harness.
Check for the proper mating.
Check the exposed wires for nicks and abrasions.
Check for moisture, dirt, or corrosion.
Check the pin/socket for a proper fit.
Disconnect the J1 machine harness connector from the Machine ECM.
Connect a jumper wire between the manual mode contact J1-24 (wire R987-PU) and the auto mode contact J1-25 (wire H728-GN).
Disconnect the machine harness at the switch.
Measure the resistance between contact 1 (wire H728-GN) and contact 3 (wire R987-PU) at the connector for the switch.Expected Result:The resistance should be less than 5 ohms.Results:
OK - The resistance is less than 5 ohms. The machine harness is correct. Proceed to test step 3.
NOT OK - The resistance is greater than 5 ohms. There is an open in the machine harness. The open exists in the wire with the high resistance.Repair: There is an open or bad connection in switch input wire H728-GN or wire R987-PU. Refer to the complete machine Electrical System Schematic. Check the connectors that are in the switch circuits for loose or corroded connections. Repair the machine harness or replace the machine harness. STOPTest Step 3. CHECK IF THE DIAGNOSTIC CODE IS STILL ACTIVE.
Inspect the harness connectors. Clean the contacts of the harness connectors and check the wires for damage to the insulation that is caused by excessive heat, corrosion, or chafing.
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the circuit.
Reconnect all harness connectors. Make sure that the connectors are fully seated and that the clips for each connector are completely fastened.
Turn the disconnect switch and the key start switch to the ON position.
Operate the machine.
Determine if the CID 2659 FMI 02 is active.Expected Result:The CID 2659 FMI 02 is active.Results:
YES - The CID 2659 FMI 02 is active. The problem


Parts ring Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.